61816-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61816-ZZ-NTN model number is decoded

61816-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 16 by five gives the 80 mm bore; the 100 mm outside diameter and 10 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 80 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN catalogue order number: 6816ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 80 mm bore the ring mass is significant: heat 61816 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• Only 10.0 mm of radial section separates bore and OD on the 618xx series at 80 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6216.
• ZZ shields are non-contact: 61816-ZZ-NTN blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 61816-2RS for that.
• Shielded 61816-ZZ-NTN units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 100 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61816-ZZ-NTN.
• NTN catalogues the shielded version as 6816ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• At 80 mm bore 61816 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 6000 r/min the grease limiting speed for 61816 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• NTN rates 61816 at 14 kN dynamic (C) and 13.3 kN static (C0), 0.89 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 154 g, 61816 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 80×100×10 mm envelope of 61816 gives a D/d ratio of 1.25 and only 10.0 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 14/13.3 kN load ratings, 0.89 kN fatigue load limit Cu NTN lists the grease limiting speed at 6000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 154 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6816ZZ on the 80×100×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61816 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61816 is listed.