61900-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61900-NTN model number is decoded

61900 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 10 by five gives the 10 mm bore; the 22 mm outside diameter and 6 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 10 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 10 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 61900 with C3 clearance and re-check the residual value after mounting.
• The 619xx thin section (6.0 mm section height at 10 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• The open 61900-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 10×22×6 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 61900-NTN leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Vibration during standstill brinells the raceways of a 10 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Do not quieten a noisy bearing by preloading it: the 61900-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 61900 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• At 10 mm bore the 61900 sits in NTN's miniature range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• The 30000 r/min grease limiting speed puts 61900 in NTN's high-speed range; at these speeds relubrication interval shortens sharply and the pressed-steel cage must be checked for cage-bar critical speed.
• At 2.99 kN dynamic load rating (C) and 1.27 kN static (C0), 0.1 kN fatigue load limit Cu, 61900 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 9 g, 61900 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 10×22×6 mm envelope of 61900 gives a D/d ratio of 2.20 and 6.0 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 2.99/1.27 kN load ratings, 0.1 kN fatigue load limit Cu NTN lists the grease limiting speed at 30000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 9 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6900 on the 10×22×6 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61900 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.