61900-ZZ bearing: complete specifications & equivalents
The 61900-ZZ is a ISO 15 radial bearing sized 10 x 22 x 6 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 10 mm |
| Outer diameter D | 22 mm |
| Width B | 6 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 2.7 kN |
| Basic static load rating C0 | 1.27 kN |
| Fatigue load limit Pu | 0.054 kN |
| Reference speed (thermal) | 70000 rpm |
| Limiting speed (mechanical) | 36000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 10 g |
| Manufacturer designation | SKF 61900-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 0.866 in |
| Width B | 0.236 in |
| ISO bore code | 00 |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in 61900-series | 10 mm |
| Largest outer diameter in 61900-series | 420 mm |
| Width range across 61900-series | 6–56 mm |
| Bore position in 61900-series (smallest first) | 1 of 35 |
| Bore above smallest 61900-series size | 0 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61900 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range. Brand-specific OEM equivalents pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61900-ZZ model number is decoded
In the 61900-series (ISO 15 diameter series 9) the last two digits encode the bore: 61900 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 22 mm and width 6 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 10 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- textile machinery
- packaging machinery
- space-constrained gearboxes
- clutch and transmission assemblies
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- rolling-contact fatigue spalling after the rated L10 life is exceeded
- brinelling from static overload or hammering during mounting
Selection pitfalls — read before you substitute
- Bore codes 00–03 use the exception table: 61900 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).
- The 619xx thin section (6.0 mm section height at 10 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
- ZZ shields are non-contact: 61900-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 61900-2RS for that.
- Shielded 61900-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
- Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
- SKF spells the shielded version 61900-2Z (one shield: 61900-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The 2.7/1.27 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61900-ZZ bearing?
A 61900-ZZ deep-groove ball bearing has a 10 mm bore, 22 mm outer diameter and 6 mm width (0.394 × 0.866 × 0.236 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields.
Why does 61900 not follow the bore-code × 5 rule?
Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 61900 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm).
What does the ZZ suffix on 61900-ZZ mean?
ZZ means two non-contact sheet-metal shields, one each side. They retain factory grease and block coarse particles with little friction, but do not seal against liquids, fine dust or pressure washing.
How does the 61900 compare with other series at the same 10 mm bore?
619 is a thin section one step above 618: 22×6 mm with a 6.0 mm radial section at 10 mm bore; a 6200 on the same bore is substantially larger and more heavily rated.
What is the SKF designation and catalogue data for 61900-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 61900-2Z — two non-contact sheet-metal shields, 10×22×6 mm per ISO 15. Quoted values: C 2.7 kN, C0 1.27 kN, Pu 0.054 kN, limiting speed 36000 r/min, mass 10 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61900-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.