61922-2RS bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61922-2RS model number is decoded

61922-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 22 by five gives the 110 mm bore; the 150 mm outside diameter and 20 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 110 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's contact-seal catalogue number is 6922DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 619xx thin section (20.0 mm section height at 110 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• Contact seals add drag and heat: 61922-2RS runs slower and cooler-limited than the open 61922; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Heat is the enemy of the sealed 61922-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• A 110 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Never mix components between two 61922-2RS units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• NSK catalogues the contact-sealed version as 6922DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. NSK's DDU lip design is single-lip contact, so grease life is longer than VV but drag torque is higher.
• At 110 mm bore 61922 is in NSK's medium industrial range; the pressed-steel cage is standard, but large-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• NSK rates 61922 at 48 kN dynamic (C) and 44.5 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 893 g, 61922 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 110×150×20 mm envelope of 61922 gives a D/d ratio of 1.36 and only 20.0 mm radial section height — this is an ultra-thin section in NSK's E1103 catalogue where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 48/44.5 kN load ratings, mass 893 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6922DDU on the 110×150×20 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61922 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.