61922-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61922-ZZ-NTN model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61922 carries bore code 22 = 110 mm. Outside diameter 150 mm and width 20 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 110 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN catalogue order number: 6922ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 110 mm of 61922-ZZ-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 619xx thin section (20.0 mm section height at 110 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• Do not wash 61922-ZZ-NTN in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Shielded 61922-ZZ-NTN units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Measure the shaft, do not trust the drawing: a 110 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61922-ZZ-NTN.
• The housing bore for the 150 mm OD should be round within IT7; an oval bore pinches the outer ring of 61922-ZZ-NTN and shows up later as two-point loaded raceway wear.
• NTN catalogues the shielded version as 6922ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• At 110 mm bore 61922 is in NTN's medium industrial range; the pressed-steel cage is standard but large-section 63xx/64xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 4100 r/min for 61922; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• NTN rates 61922 at 48.5 kN dynamic (C) and 44.5 kN static (C0), 2.6 kN fatigue load limit Cu; this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 849 g, 61922 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 110×150×20 mm envelope of 61922 gives a D/d ratio of 1.36 and only 20.0 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 48.5/44.5 kN load ratings, 2.6 kN fatigue load limit Cu NTN lists the grease limiting speed at 4100 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 849 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6922ZZ on the 110×150×20 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61922 in a rated drive.
• Standard catalogue stock of 61922 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.