6205-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6205-NTN model number is decoded

6205 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 05 by five gives the 25 mm bore; the 52 mm outside diameter and 15 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 25 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 6205-NTN; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• At 25 mm bore the 62xx light series is the workhorse section; its 52×15 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• The open 6205-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 25×52×15 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6205 units.
• Measure the shaft, do not trust the drawing: a 25 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6205-NTN.
• A 25 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• The open 6205 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 25 mm bore puts 6205 in NTN's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• NTN rates 6205 at 13000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the housing.
• At 15.5 kN dynamic load rating (C) and 7.85 kN static (C0), 0.55 kN fatigue load limit Cu, 6205 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 128 g, 6205 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 25×52×15 mm envelope of 6205 gives a D/d ratio of 2.08 and 13.5 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 15.5/7.85 kN load ratings, 0.55 kN fatigue load limit Cu NTN lists the grease limiting speed at 13000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 128 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6205 on the 25×52×15 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6205 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• Standard catalogue stock of 6205 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.