6205-ZZ-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6205-ZZ-FAG model number is decoded

6205-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 05 by five gives the 25 mm bore; the 52 mm outside diameter and 15 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 25 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogue order number: 6205-C-2Z (FAG suffix 2Z), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 6205-ZZ-FAG; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• The 62xx light series is the default general-purpose section at 25 mm bore; before upgrading to a 6305 for extra capacity, confirm the housing accepts a 52 mm OD and 15 mm width — it is not a drop-in swap.
• Do not wash 6205-ZZ-FAG in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Shielded 6205-ZZ-FAG units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 15 mm-wide ring of 6205-ZZ-FAG drags the lip and overheats it.
• Schaeffler HR 1 lists the shielded version as 6205-C-2Z — FAG suffix 2Z, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the FAG order number when buying through a Schaeffler channel.
• FAG rates 6205 at 18400 r/min mechanical limiting speed (thermal reference speed 16000 r/min) — a high-speed range where the thermal reference speed governs continuous duty; use low-viscosity turbine oil or high-speed grease and avoid lip-contact seals entirely.
• The 25 mm bore puts 6205 in Schaeffler's light industrial range; the standard cage and CN clearance cover most fractional-horsepower motor and small-pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• At 15.9 kN dynamic load rating (C) and 7.8 kN static (C0), 6205 is a medium-load FAG bearing for most electric-motor and pump duty; check the static safety factor against C0 for preloaded or thrust-loaded arrangements.
• At 130 g, 6205 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 25×52×15 mm envelope of 6205 gives a D/d ratio of 2.08 and 13.5 mm radial section height — a heavy FAG section for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 15.9/7.8 kN load ratings, mass 130 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6205-C-2Z on the 25×52×15 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6205 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 6205; the standard NBR lip is the economical general-duty choice, not the high-temperature one.
• FAG standard tolerance for this size is P0 (PN); P6/P5 precision executions exist for spindle-adjacent duty but carry different order numbers in the Schaeffler system — they are not a selectable sorting of standard stock.