6205-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6205-ZZ-NTN model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6205 carries bore code 05 = 25 mm. Outside diameter 52 mm and width 15 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 25 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN catalogue order number: 6205ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 25 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 6205-ZZ-NTN.
• The 62xx light series is the default general-purpose section at 25 mm bore; before upgrading to a 6305 for extra capacity, confirm the housing accepts a 52 mm OD and 15 mm width — it is not a drop-in swap.
• Do not wash 6205-ZZ-NTN in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Shielded 6205-ZZ-NTN units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Shaft and housing fillets must clear the bearing chamfer so the 15 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• Never mix components between two 6205-ZZ-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• NTN catalogues the shielded version as 6205ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• The 25 mm bore puts 6205 in NTN's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• At 11000 r/min the grease limiting speed for 6205 covers most general-purpose industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• At 15.5 kN dynamic load rating (C) and 7.85 kN static (C0), 0.55 kN fatigue load limit Cu, 6205 is a medium-load bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NTN catalogue.
• At 128 g, 6205 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 25×52×15 mm envelope of 6205 gives a D/d ratio of 2.08 and 13.5 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 15.5/7.85 kN load ratings, 0.55 kN fatigue load limit Cu NTN lists the grease limiting speed at 11000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 128 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6205ZZ on the 25×52×15 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6205 in a rated drive.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.
• Standard catalogue stock of 6205 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.