W6200 bearing: complete specifications & equivalents
The W6200 is a ISO 15 radial bearing sized 10 x 30 x 9 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 30 mm |
| Width B | 9 mm |
| Material | SS440C |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 4.36 kN |
| Basic static load rating C0 | 2.32 kN |
| Fatigue load limit Pu | 0.1 kN |
| Reference speed (thermal) | 60000 rpm |
| Limiting speed (mechanical) | 36000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 28 g |
| Manufacturer designation | W 6200 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 1.181 in |
| Width B | 0.354 in |
| ISO bore code | 00 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 7 of 45 |
| Bore above smallest 6200-series size | 7 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| W6200-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 10×30×9 mm envelope and equivalent catalogue ratings; W 6200-2RS1 is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W6200-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 10×30×9 mm envelope and equivalent catalogue ratings; W 6200-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 6200 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6200 shares the 10×30×9 mm envelope but carries different catalogue ratings (4.36/2.32 kN vs 5.4/2.36 kN) — the stainless execution is not a load-rating equivalent. |
| 6200-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6200-2Z shares the 10×30×9 mm envelope but carries different catalogue ratings (4.36/2.32 kN vs 5.4/2.36 kN) — the stainless execution is not a load-rating equivalent. |
| 6200-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6200-2RSH shares the 10×30×9 mm envelope but carries different catalogue ratings (4.36/2.32 kN vs 5.4/2.36 kN) — the stainless execution is not a load-rating equivalent. |
| 6200-RSR | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6200-2RSL shares the 10×30×9 mm envelope but carries different catalogue ratings (4.36/2.32 kN vs 5.4/2.36 kN) — the stainless execution is not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the W6200 model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 6200-series, bore code 00 follows the 10/12/15/17 mm exception table, so 6200 fits a 10 mm shaft. Envelope 10×30×9 mm (0.394×1.181×0.354 in), C 4.36 kN, C0 2.32 kN, Pu 0.1 kN; limiting speed 36000 r/min and mass 28 g. The open W 6200 carries no shields or seals and relies on application lubrication and external sealing. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- appliances exposed to moisture
- food and beverage conveyors
- pharmaceutical and packaging machines
- washdown-duty equipment
Known failure patterns
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- seal and grease failure before the rings corrode in sustained washdown service
- contamination wear when the open arrangement is used without external seals
- lubricant starvation where no regreasing interval is maintained
Selection pitfalls — read before you substitute
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W6200 is not marine-grade stainless.
- The stainless steel is martensitic and MAGNETIC; do not reject W6200 over magnetism — only austenitic grades are non-magnetic, and those are too soft for bearing raceways.
- Stainless bearings carry lower load ratings than chrome steel of the same envelope: W6200 is quoted at C 4.36 kN versus the 9 mm-wide 52100 version — do not swap on dimensions alone.
- Food, pharmaceutical and washdown positions need food-grade grease (e.g. NSF H1 registered) inside W6200; standard fill is industrial grease unless specified otherwise.
- The fatigue load limit is 0.1 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- Catalogue ratings for W6200 (C 4.36 kN, C0 2.32 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
Frequently asked questions
What are the dimensions of the stainless W6200?
SKF W 6200 measures 10×30×9 mm (0.394×1.181×0.354 in), about 28 g, C 4.36 kN.
What does the W in W 6200 mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
What grease is supplied in W6200?
The open bearing may ship with a rust-preventive film only; specify a food-grade grease for HACCP areas and plan relubrication.
Are W stainless bearings waterproof?
No — the stainless rings resist moisture and weak chemicals far better than 52100 chrome steel, but salt spray, strong chlorides and unlubricated washdown duty can still corrode W6200; add seals and food-grade grease for wet positions.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.