6300-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6300-NSK model number is decoded

6300 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the medium 63xx section (diameter series 3 of ISO 15), multiplying bore code 10 by five gives the 10 mm bore; the 35 mm outside diameter and 11 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 10 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 10 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6300 with C3 for those conditions.
• The 63xx medium series gains rating at 10 mm bore through a 35 mm OD and 11 mm width; the heavier rolling elements also trade away some speed versus a 6210.
• The open 6300-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 10×35×11 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 6300-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Do not quieten a noisy bearing by preloading it: the 6300-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• The open 6300 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• At 10 mm bore the 6300 sits in NSK's miniature range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• NSK rates 6300 at 8.9 kN dynamic (C) and 3.45 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 52 g, 6300 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 10×35×11 mm envelope of 6300 gives a D/d ratio of 3.50 and 12.5 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 8.9/3.45 kN load ratings, mass 52 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6300 on the 10×35×11 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6300 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 6300; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.