6302-RSR-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6302-RSR-NSK model number is decoded

In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6302 carries bore code 15 = 15 mm. Outside diameter 42 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 15 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK's non-contact seal suffix is VV (catalogue number 6302VV), mapped here from the industry-neutral -RSR spelling; speed capability is close to the open bearing but VV is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 15 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6302 with C3 clearance and re-check the residual value after mounting.
• The 63xx medium section at 15 mm bore gains dynamic rating through larger rolling elements on a 42 mm OD; the penalty is mass and a lower limiting speed than the 6215 — do not specify it for speed-critical shafts.
• RSR low-friction seals on 6302-RSR-NSK run faster than contact-seal 6302-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6302-2RS instead.
• The non-contact lip of 6302-RSR-NSK does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 15 mm bore position before relying on it as sealed-for-life.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 13 mm-wide ring of 6302-RSR-NSK drags the lip and overheats it.
• Measure the shaft, do not trust the drawing: a 15 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6302-RSR-NSK.
• NSK catalogues this low-friction non-contact seal as 6302VV (suffix VV), mapped here from the industry-neutral -RSR spelling. NSK rates its speed capability close to the open bearing, but VV is not liquid-tight — for wet or fine-dust duty step up to the DDU contact seal (industry-neutral -2RS).
• At 15 mm bore the 6302 sits in NSK's small-bore range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• NSK rates 6302 at 12.6 kN dynamic (C) and 5.45 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 83 g, 6302 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 15×42×13 mm envelope of 6302 gives a D/d ratio of 2.80 and 13.5 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 12.6/5.45 kN load ratings, mass 83 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6302VV on the 15×42×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6302 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.
• NSK's VV non-contact seal keeps frictional torque close to the open 6302; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.