6302-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6302-2RS-FAG model number is decoded

6302-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the medium 63xx section (diameter series 3 of ISO 15), multiplying bore code 15 by five gives the 15 mm bore; the 42 mm outside diameter and 13 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogues the lip-contact sealed version as 6302-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 15 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6302 with C3 clearance and re-check the residual value after mounting.
• The 63xx medium section at 15 mm bore gains dynamic rating through larger rolling elements on a 42 mm OD; the penalty is mass and a lower limiting speed than the 6215 — do not specify it for speed-critical shafts.
• Heat is the enemy of the sealed 6302-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6302-2RS-FAG in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Vibration during standstill brinells the raceways of a 15 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 13 mm-wide ring of 6302-2RS-FAG drags the lip and overheats it.
• Schaeffler HR 1 lists the lip-contact sealed version as 6302-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• FAG rates 6302 at 17700 r/min mechanical limiting speed — electric-motor territory; prefer the open or 2Z execution (sealed 2RSR variants lose roughly a third of the thermal speed) and confirm grease life at the reference speed for continuous running.
• At 15 mm bore the 6302 sits in Schaeffler's small-bore range; HR 1 ships these sizes with a pressed steel or plastic cage and P0 tolerance as standard — for instrument or spindle accuracy order the P6/P5 variant explicitly, since P0 runout figures will not hold.
• FAG rates 6302 at 13.3 kN dynamic (C) and 5.3 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At 83 g, 6302 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 15×42×13 mm envelope of 6302 gives a D/d ratio of 2.80 and 13.5 mm radial section height — a heavy FAG section for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 13.3/5.3 kN load ratings, mass 83 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6302-C-2HRS on the 15×42×13 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6302 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler's medias/eKatalog is the live source for the current execution of 6302: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.
• Mixing old and new FAG generations of the same designation in one arrangement is dimensionally acceptable, but where ratings matter — preloaded or matched sets — order both positions from the same generation and lot.