6302-RSR bearing: complete specifications & equivalents
The 6302-RSR is a ISO 15 radial bearing sized 15 x 42 x 13 mm (bore x OD x width) with RSR sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 15 mm |
| Outer diameter D | 42 mm |
| Width B | 13 mm |
| Material | GCr15 |
| Seal / shield | RSR |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 11.9 kN |
| Basic static load rating C0 | 5.4 kN |
| Fatigue load limit Pu | 0.228 kN |
| Reference speed (thermal) | 38000 rpm |
| Limiting speed (mechanical) | 19000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 85 g |
| Manufacturer designation | SKF 6302-2RSL |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6300-series range
| Bore d | 0.591 in |
|---|---|
| Outer diameter D | 1.654 in |
| Width B | 0.512 in |
| ISO bore code | 02 |
| Radial section height (D−d)/2 | 13.5 mm |
| Smallest bore in 6300-series | 2 mm |
| Largest outer diameter in 6300-series | 500 mm |
| Width range across 6300-series | 3–95 mm |
| Bore position in 6300-series (smallest first) | 7 of 40 |
| Bore above smallest 6300-series size | 13 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6302-2RS-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant (RSR vs 2RS) and load ratings differ — confirm sealing and rating before substituting. |
| 6302-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting. |
| 6302-ZZ-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant (RSR vs ZZ) and load ratings differ — confirm sealing and rating before substituting. |
| 6302 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
| 6302-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant differs (RSR vs 2RS) — confirm sealing suits the duty. |
| 6302-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty. |
| 6302-RSR-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6302-ZZ-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
| 6302-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant differs (RSR vs 2RS) — confirm sealing suits the duty. |
| 6302-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty. |
| 6302-RSR-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6302-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×42×13 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
| 7302 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| W6302-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6302-2RS1 shares the 15×42×13 mm envelope but rates differently (11.9/5.4 kN vs 9.95/5.4 kN) — not a load-rating equivalent. |
| W6302-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6302-2Z shares the 15×42×13 mm envelope but rates differently (11.9/5.4 kN vs 9.95/5.4 kN) — not a load-rating equivalent. |
| W6302 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6302 shares the 15×42×13 mm envelope but rates differently (11.9/5.4 kN vs 9.95/5.4 kN) — not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6302-RSR model number is decoded
6302-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the medium 63xx section (diameter series 3 of ISO 15), its bore code 02 comes from the 10/12/15/17 mm exception table, giving a 15 mm bore; the 42 mm outside diameter and 13 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. SKF's low-friction seal suffix is 2RSL/2RZ (this page's industry-neutral spelling is -RSR); catalogue number 6302-2RSL.
Typical equipment & failure modes
Common applications
- fractional-horsepower electric motors
- domestic appliances
- power tools
- small fans and blowers
Known failure patterns
- ingress of fine dust or moisture past the non-contact lip in dirty or wet duty (RSR is not liquid-tight)
- lip-lubricant starvation if the bearing runs dry for extended periods
- electrical pitting in VFD-driven motors without grounding protection
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Codes 00–03 are the exception series: 6302 takes its 15 mm bore from the 10/12/15/17 mm table, so two designations only a few millimetres apart can read alike on paper — order by measured shaft size, not by code arithmetic.
- The 63xx medium series gains rating at 15 mm bore through a 42 mm OD and 13 mm width; the heavier rolling elements also trade away some speed versus a 6202.
- RSR low-friction seals on 6302-RSR run faster than contact-seal 6302-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6302-2RS instead.
- The non-contact lip of 6302-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 15 mm bore position before relying on it as sealed-for-life.
- The housing bore for the 42 mm OD should be round within IT7; an oval bore pinches the outer ring of 6302-RSR and shows up later as two-point loaded raceway wear.
- Shaft and housing fillets must clear the bearing chamfer so the 13 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
- SKF catalogues the low-friction seal as 6302-2RSL (suffix -2RSL or -2RZ): a non-contact elastomer lip that runs near the open 19000 r/min limiting speed, closer to the open bearing's 38000 r/min reference than the contact-seal version. It keeps coarse debris out without the drag of a contact seal, but is not liquid-tight — use 2RSH for wet or fine-dust positions.
- The 11.9/5.4 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6302-RSR bearing?
A 6302-RSR deep-groove ball bearing has a 15 mm bore, 42 mm outer diameter and 13 mm width (0.591 × 1.654 × 0.512 in), per ISO 15 boundary dimensions. It is fitted with two low-friction non-contact rubber seals.
What internal clearance does 6302-RSR have?
Unless a clearance suffix says otherwise, 6302-RSR is manufactured to normal (CN) radial internal clearance. Tight fits and hot shafts consume clearance in service — for those conditions order the C3 execution of 6302 and verify the residual clearance after mounting.
How should 6302-RSR be mounted?
Apply the mounting force to the ring being fitted: on a 15 mm shaft seat the press load must pass through the inner-ring face only. A fitting sleeve and an arbor press are normally sufficient at this size. Never strike the outer ring, the cage or the seals.
What lubrication does 6302-RSR need?
6302-RSR is supplied pre-greased for life and is not designed to be opened for relubrication; where a relubrication path is required, specify the open 6302 with a housing grease fitting instead.
What is the SKF designation and catalogue data for 6302-RSR?
In the SKF Rolling Bearings catalogue this size is listed as 6302-2RSL — two low-friction non-contact elastomer seals, 15×42×13 mm per ISO 15. Quoted values: C 11.9 kN, C0 5.4 kN, Pu 0.228 kN, limiting speed 19000 r/min, mass 85 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6302-RSR.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.