6317-ZZ bearing: complete specifications & equivalents
The 6317-ZZ is a ISO 15 radial bearing sized 85 x 180 x 41 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 85 mm |
| Outer diameter D | 180 mm |
| Width B | 41 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 140 kN |
| Basic static load rating C0 | 96.5 kN |
| Fatigue load limit Pu | 3.55 kN |
| Reference speed (thermal) | 8000 rpm |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 4400 g |
| Manufacturer designation | SKF 6317-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6300-series range
| Bore d | 3.346 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 1.614 in |
| ISO bore code | 17 |
| Radial section height (D−d)/2 | 47.5 mm |
| Smallest bore in 6300-series | 10 mm |
| Largest outer diameter in 6300-series | 400 mm |
| Width range across 6300-series | 11–78 mm |
| Bore position in 6300-series (smallest first) | 18 of 30 |
| Bore above smallest 6300-series size | 75 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6317 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range. Brand-specific OEM equivalents pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6317-ZZ model number is decoded
In the 6300-series (ISO 15 diameter series 3) the last two digits encode the bore: 6317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 41 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 85 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's own suffix is 2Z (this page's industry-neutral spelling is -ZZ); catalogue number 6317-2Z.
Typical equipment & failure modes
Common applications
- hoists and winches
- heavy conveyors
- pulp and paper machinery
- medium and heavy industrial drives
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- raceway smearing under marginal lubrication at start-up
- edge loading from shaft deflection or housing misalignment
Selection pitfalls — read before you substitute
- Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 63xx medium series gains rating at 85 mm bore through a 180 mm OD and 41 mm width; the heavier rolling elements also trade away some speed versus a 6217.
- ZZ shields are non-contact: 6317-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6317-2RS for that.
- Shielded 6317-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
- Do not quieten a noisy bearing by preloading it: the 6300-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- SKF spells the shielded version 6317-2Z (one shield: 6317-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The single-shield execution 6317-Z is a distinct order number in catalogue 17000: it suits open gears or oil-bath arrangements where the unshielded face faces the lubricant, and it is not interchangeable with the double-shield 6317-2Z for high-contamination positions.
- The 140/96.5 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6317-ZZ bearing?
A 6317-ZZ deep-groove ball bearing has a 85 mm bore, 180 mm outer diameter and 41 mm width (3.346 × 7.087 × 1.614 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields. Geometry-based estimated mass is about 4136 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6317 bore code work?
The last two digits of 6317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 41 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the ZZ suffix on 6317-ZZ mean?
ZZ means two non-contact sheet-metal shields, one each side. They retain factory grease and block coarse particles with little friction, but do not seal against liquids, fine dust or pressure washing.
How does the 6300 compare with other series at the same 85 mm bore?
The '3' is the medium diameter series: 180×41 mm, 47.5 mm radial section at 85 mm bore, carrying more load than a 6217 but needing a larger housing bore and giving up some speed.
What is the SKF designation and catalogue data for 6317-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 6317-2Z — two non-contact sheet-metal shields, 85×180×41 mm per ISO 15. Quoted values: C 140 kN, C0 96.5 kN, Pu 3.55 kN, limiting speed 4000 r/min, mass 4400 g. Brand suffixes (2Z, 2RSH) differ from the industry-neutral spelling 6317-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.