6317 bearing: complete specifications & equivalents
The 6317 is a ISO 15 radial bearing sized 85 x 180 x 41 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 85 mm |
| Outer diameter D | 180 mm |
| Width B | 41 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 140 kN |
| Basic static load rating C0 | 96.5 kN |
| Fatigue load limit Pu | 3.55 kN |
| Reference speed (thermal) | 8000 rpm |
| Limiting speed (mechanical) | 5000 rpm |
| Operating temperature | -40 to +150 °C |
| Mass | 4250 g |
| Manufacturer designation | SKF 6317 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6300-series range
| Bore d | 3.346 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 1.614 in |
| ISO bore code | 17 |
| Radial section height (D−d)/2 | 47.5 mm |
| Smallest bore in 6300-series | 10 mm |
| Largest outer diameter in 6300-series | 400 mm |
| Width range across 6300-series | 11–78 mm |
| Bore position in 6300-series (smallest first) | 18 of 30 |
| Bore above smallest 6300-series size | 75 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6317 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6317 model number is decoded
In the 6300-series (ISO 15 diameter series 3) the last two digits encode the bore: 6317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 41 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 85 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the SKF catalogue this open execution carries the bare designation; protected variants are ordered separately as -2Z and -2RSH.
Typical equipment & failure modes
Common applications
- hoists and winches
- heavy conveyors
- pulp and paper machinery
- medium and heavy industrial drives
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- fretting corrosion on a loose shaft seat
- cage damage from operation beyond the limiting speed
Selection pitfalls — read before you substitute
- Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 63xx medium series gains rating at 85 mm bore through a 180 mm OD and 41 mm width; the heavier rolling elements also trade away some speed versus a 6217.
- The open 6317 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×180×41 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 6300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6317 units.
- Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
- The open 6317 needs external sealing and application-supplied lubrication; in the SKF catalogue the protected variants are separate order numbers 6317-2Z (shields) and 6317-2RSH (contact seals), not suffix-free 6317.
- The 140/96.5 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6317 bearing?
A 6317 deep-groove ball bearing has a 85 mm bore, 180 mm outer diameter and 41 mm width (3.346 × 7.087 × 1.614 in), per ISO 15 boundary dimensions. It is an open bearing with no seals or shields. Geometry-based estimated mass is about 4136 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6317 bore code work?
The last two digits of 6317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 41 mm width follow the ISO 15 diameter series, not the bore code alone.
What does no suffix on 6317 mean?
A bare 6317 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 6300 compare with other series at the same 85 mm bore?
The '3' is the medium diameter series: 180×41 mm, 47.5 mm radial section at 85 mm bore, carrying more load than a 6217 but needing a larger housing bore and giving up some speed.
What is the SKF designation and catalogue data for 6317?
In the SKF Rolling Bearings catalogue this size is listed as 6317 — the open (unsealed) execution, 85×180×41 mm per ISO 15. Quoted values: C 140 kN, C0 96.5 kN, Pu 3.55 kN, limiting speed 5000 r/min, mass 4250 g. Brand suffixes (2Z, 2RSH) differ from the industry-neutral spelling 6317.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.