C2212-V bearing: complete specifications & equivalents
The C2212-V is a ISO 15 radial bearing sized 60 x 110 x 28 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 60 mm |
| Outer diameter D | 110 mm |
| Width B | 28 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 166 kN |
| Basic static load rating C0 | 190 kN |
| Fatigue load limit Pu | 22.4 kN |
| Limiting speed (mechanical) | 2800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1150 g |
| Manufacturer designation | C 2212 V |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & C2200-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 1.102 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 25 mm |
| Smallest bore in C2200-series | 30 mm |
| Largest outer diameter in C2200-series | 400 mm |
| Width range across C2200-series | 20–108 mm |
| Bore position in C2200-series (smallest first) | 7 of 21 |
| Bore above smallest C2200-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| C2212-TN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 60×110×28 mm envelope, but catalogue C/C0 differ between the cylindrical-bore full-complement V and cylindrical-bore TN9 PA66-caged executions (166/190 kN vs 143/156 kN) — envelope match, not a load-rating equivalent. |
| C2212-KTN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 60×110×28 mm envelope, but catalogue C/C0 differ between the cylindrical-bore full-complement V and 1:12 tapered-bore K TN9 PA66-caged executions (166/190 kN vs 143/156 kN) — envelope match, not a load-rating equivalent. |
| C2212-KV | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 60×110×28 mm ISO 15 envelope and equivalent catalogue C/C0; C 2212 KV is the 1:12 tapered-bore K full-complement V execution of this size — boundary dimensions interchangeable, only mounting and cage execution differ. |
| 22212 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 60×110×28 mm envelope as the SKF spherical roller bearing SKF 22212 E, but catalogue C/C0 differ (166/190 kN vs 159/166 kN) — and the functions differ: spherical locates axially, CARB floats. Pair them; never swap one-for-one. |
| 22212-EK | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 60×110×28 mm envelope as the SKF spherical roller bearing SKF 22212 EK, but catalogue C/C0 differ (166/190 kN vs 159/166 kN) — and the functions differ: spherical locates axially, CARB floats. Pair them; never swap one-for-one. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the C2212-V model number is decoded
In SKF catalogue PUB BU/P1 17000, C 2212 V denotes a toroidal roller bearing whose 28 mm long rollers crown at both ends: the contact accepts angular misalignment while the ring positions float, which is why CARB bearings are specified at the free shaft end. Reading the code: C marks the CARB toroidal family, the first two digits (22) identify the ISO dimension series and the last two (12) encode the 60 mm bore; suffixes describe bore and execution. The open execution relies on the housing seals and lubrication system, fed through groove/hole features on the large sizes. Explorer-class heat treatment and the crowned roller profile keep edge stress down when the 60 mm shaft deflects; no reference speed is listed and the limiting speed is 2,800 r/min. The 1150 g mass over the 60×110×28 mm envelope yields about 2.77 kN dynamic per millimetre of bore — the long toroidal rollers give this family its radial capacity density. Open executions accept relubrication — route it through the outer-ring groove on sizes that have one and purge stale grease at service intervals. Grease through the annular groove features where provided; on open executions feed lubricant past the long roller set at assembly, since the 28 mm wide cavity does not fill itself.
Typical equipment & failure modes
Common applications
- heavy industrial gearbox layshafts used as the non-locating position
- winder and reel drums in paper and steel strip plants
- paper machine drying cylinders and calender rolls with long, thermally expanding shafts
- continuous-caster guide rolls and slab-caster segments under heat growth
Known failure patterns
- roller-end and flange smearing after lubricant starvation at the long roller contacts
- edge loading and premature spalling when the CARB position is blocked from its designed axial float
- brass cage pocket wear under marginal lubrication in the large-bore M/MB executions
- condensation pitting in machines that run intermittently in humid environments
- grease churning and overheating when a high-speed thrust position is over-packed
Selection pitfalls — read before you substitute
- At 60 mm bore the small CARB executions are unusually wide (28 mm) for their 110 mm OD — confirm the housing width before substituting a standard spherical bearing of the same bore.
- Tapered-bore K executions mount on adapter sleeves (1:12) and K30 on withdrawal sleeves (1:30) — the 60 mm bore changes the sleeve family, and the drive-up procedure differs accordingly.
- Reference and limiting speeds are different limits: the catalogue lists no thermal reference speed for this full-complement/sealed execution, the limiting value is the mechanical ceiling; observe the reference under load unless the arrangement calculation says otherwise.
- Never use C 2212 V as the locating bearing: it carries no axial load by design — the arrangement needs a separate locating spherical, tapered or angular bearing facing the thrust.
- The quoted 166/190 kN ratings belong to this exact execution (C 2212 V); VE240 vibrating-screen variants and sealed 2CS/2NS variants have their own figures even at the same envelope.
- The 166/190 kN ratings and 1150 g mass are SKF catalogue values transcribed from ch. 10.1 of PUB BU/P1 17000 (PDF table page 858); mounting data — axial displacement (s) and seating details — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
Why is C 2212 V used opposite a spherical roller bearing?
The spherical bearing locates the shaft and takes thrust; the CARB bearing at the other end self-aligns but floats, absorbing thermal expansion without inducing axial load. The pair is standard on paper machine drying cylinders and long caster rolls.
Is the C 2212 V sealed?
No, it is an open execution relying on the housing seals; the full-complement V design has no thermal reference speed in the catalogue.
What fails first on a misapplied CARB bearing?
Blocking the designed axial float — clamping the free end or locating both shaft ends — turns thermal growth into edge loading and spalls the toroidal raceways. Cage damage and ordinary fatigue follow overload or dry running.
Which dimensions does the C 2212 V have?
A C 2212 V measures 60 mm bore × 110 mm outside diameter × 28 mm width (2.362 × 4.331 × 1.102 in). From SKF catalogue PUB BU/P1 17000: dynamic C 166 kN, static C0 190 kN, fatigue limit Pu 22.4 kN, limiting speed 2,800 r/min, no reference speed listed, mass about 1150 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 10.1 CARB toroidal roller bearings on 2026-09-27. Read our editorial & correction policy.