N224-ECP bearing: complete specifications & equivalents
The N224-ECP is a ISO 15 radial bearing sized 120 x 215 x 40 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 120 mm |
| Outer diameter D | 215 mm |
| Width B | 40 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 390 kN |
| Basic static load rating C0 | 430 kN |
| Fatigue load limit Pu | 49 kN |
| Reference speed (thermal) | 3400 rpm |
| Limiting speed (mechanical) | 3600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 5750 g |
| Manufacturer designation | SKF N 224 ECP |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & N200-series range
| Bore d | 4.724 in |
|---|---|
| Outer diameter D | 8.465 in |
| Width B | 1.575 in |
| ISO bore code | 24 |
| Radial section height (D−d)/2 | 47.5 mm |
| Smallest bore in N200-series | 17 mm |
| Largest outer diameter in N200-series | 230 mm |
| Width range across N200-series | 12–40 mm |
| Bore position in N200-series (smallest first) | 21 of 22 |
| Bore above smallest N200-series size | 103 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NJ224-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×215×40 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU224-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×215×40 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NUP224-ECJ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×215×40 mm and equivalent catalogue ratings; the NUP execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the N224-ECP model number is decoded
Ordering number SKF N 224 ECP resolves to a 120×215×40 mm single-row caged cylindrical roller bearing (dimension series 2 (light-section ISO 15 envelope)); two integral flanges on the inner ring and no flanges on the outer ring, so the plain outer ring is the separable part. The N configuration means two integral flanges on the inner ring and no flanges on the outer ring, so the plain outer ring is the separable part; functionally the bearing is non-locating: the outer ring can displace axially in both directions and the bearing carries radial load only. The ECP suffix marks the E-design execution with a glass-fibre reinforced polyamide (PA66) cage, limited to 120 °C continuous. Speed planning for N224-ECP: the catalogue lists 3,400 r/min thermal reference speed and 3,600 r/min mechanical limiting speed. The mass entry 5750 g covers the complete catalogue execution. Mounting: the outer ring slides in its housing seat; provide axial retention for the outer ring only if the application requires it, and let it float to absorb shaft expansion. A 120 mm seat normally takes a m6 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- mining hoist and winder shafts
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- polymer cage softening above 120 °C
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- fretting corrosion on a loose rotating shaft seat or in a vibratory stand-still
Selection pitfalls — read before you substitute
- Do not use a N bearing where axial load must be carried — the design carries radial load only
- The dimension series 2 (light-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 224, but flange configuration and axial-locating behaviour differ — quote the full SKF N 224 ECP and do not substitute rib styles without checking the shaft locating scheme.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 215 mm raceway.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 215 mm raceway.
- The 390/430 kN ratings are SKF catalogue 17000 (2018) values for the ECP execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of N224-ECP?
SKF N 224 ECP is a single-row caged cylindrical roller bearing with 120 mm bore, 215 mm OD and 40 mm width per ISO 15. SKF lists C 390 kN, C0 430 kN, Pu 49 kN, reference speed 3,400 r/min and limiting speed 3,600 r/min, mass about 5750 g.
What does the N designation and ECP suffix mean?
The ECP suffix marks the E-design execution with a glass-fibre reinforced polyamide (PA66) cage, limited to 120 °C continuous. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring, so the plain outer ring is the separable part.
Can N224-ECP take axial load and locate the shaft?
No — the plain outer ring has no flanges, so the N bearing floats axially and is for radial load; locate the shaft with a separate bearing.
How does N224-ECP compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.