NUP224-ECJ bearing: complete specifications & equivalents
The NUP224-ECJ is a ISO 15 radial bearing sized 120 x 215 x 40 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 120 mm |
| Outer diameter D | 215 mm |
| Width B | 40 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 390 kN |
| Basic static load rating C0 | 430 kN |
| Fatigue load limit Pu | 49 kN |
| Reference speed (thermal) | 3400 rpm |
| Limiting speed (mechanical) | 3600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 5950 g |
| Manufacturer designation | SKF NUP 224 ECJ |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUP200-series range
| Bore d | 4.724 in |
|---|---|
| Outer diameter D | 8.465 in |
| Width B | 1.575 in |
| ISO bore code | 24 |
| Radial section height (D−d)/2 | 47.5 mm |
| Smallest bore in NUP200-series | 17 mm |
| Largest outer diameter in NUP200-series | 480 mm |
| Width range across NUP200-series | 12–80 mm |
| Bore position in NUP200-series (smallest first) | 21 of 29 |
| Bore above smallest NUP200-series size | 103 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| N224-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×215×40 mm and equivalent catalogue ratings; the N execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NJ224-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×215×40 mm and equivalent catalogue ratings; the NJ execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU224-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 120×215×40 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NUP224-ECJ model number is decoded
In SKF catalogue PUB BU/P1 17000, SKF NUP 224 ECJ denotes a single-row caged cylindrical roller bearing on the ISO 15 120×215×40 mm envelope, dimension series 2 (light-section ISO 15 envelope), with catalogue mass 5950 g. Structurally, the NUP design has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring. In arrangement terms it is a locating bearing that positions the shaft axially in both directions while keeping the cylindrical-roller radial capacity. Reading the order-string suffix ECJ: the E-design execution with a pressed sheet-steel window cage, for positions where polymer cages are temperature- or lubricant-limited. Load-per-bore for the 120 mm seat is about 3.25 kN/mm, typical of dimension series 2 (light-section ISO 15 envelope); use C0 430 kN for static checks such as crane hook blocks standing under load. Fit practice for NUP224-ECJ: the loose inner-ring flange must be fitted on the correct side and retained by the shaft abutment; never omit it during reassembly or the bearing loses its two-direction locating function. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- offshore drawworks shafts
- large rolling-mill drive trains
- marine propulsion line shafts
- heavy turbogenerator rotor supports
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- cage pocket wear from roller skidding at insufficient radial load or during start-up before oil film build-up
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- false brinelling on standby machines exposed to external vibration
Selection pitfalls — read before you substitute
- Do not use a NUP bearing where a floating non-locating bearing is required — the loose inner flange makes it a locating bearing
- The dimension series 2 (light-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 224, but flange configuration and axial-locating behaviour differ — quote the full SKF NUP 224 ECJ and do not substitute rib styles without checking the shaft locating scheme.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 215 mm raceway.
- The 390/430 kN ratings are SKF catalogue 17000 (2018) values for the ECJ execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUP224-ECJ?
SKF NUP 224 ECJ is a single-row caged cylindrical roller bearing with 120 mm bore, 215 mm OD and 40 mm width per ISO 15. SKF lists C 390 kN, C0 430 kN, Pu 49 kN, reference speed 3,400 r/min and limiting speed 3,600 r/min, mass about 5950 g.
What does the NUP designation and ECJ suffix mean?
The ECJ suffix marks the E-design execution with a pressed sheet-steel window cage, useful where polymer cages are temperature- or lubricant-limited. Structurally this execution has two integral flanges on the outer ring plus one integral flange and one loose flange ring on the inner ring.
Can NUP224-ECJ take axial load and locate the shaft?
Yes, in both directions: the integral inner flange plus the loose flange ring close both axial paths. Do not pair it with another locating bearing without thermal clearance.
How does NUP224-ECJ compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.