MPNbase

120×215×40 mm bearings

29 models from 3 brands across 3 types share this ISO 15 envelope: 120 mm bore, 215 mm outside diameter, 40 mm width (4.724×8.465×1.575 in), 47.5 mm radial section.

29 models fit this space 3 brands 29 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6224 Deep Groove Ball SKF open CN 146 118 5250
6224-2RS Deep Groove Ball SKF 2RS CN 146 118 5350
6224-2RS-NSK Deep Groove Ball NSK 2RS CN 171 131 5290
6224-2RS-NTN Deep Groove Ball NTN 2RS CN 172 131 5150
6224-M Deep Groove Ball SKF open CN 146 118 6100
6224-NSK Deep Groove Ball NSK open CN 171 131 5290
6224-NTN Deep Groove Ball NTN open CN 172 131 5150
6224-RSR Deep Groove Ball NSK RSR CN 171 131 5290
6224-ZZ Deep Groove Ball SKF ZZ CN 146 118 5350
6224-ZZ-NSK Deep Groove Ball NSK ZZ CN 171 131 5290
6224-ZZ-NTN Deep Groove Ball NTN ZZ CN 172 131 5150
7224 Angular Contact Ball NTN open CN 202 177 6260
7224-BCBM Angular Contact Ball SKF open CN 165 163 5900
7224-BM Angular Contact Ball SKF open CN 165 163 5900
7224B Angular Contact Ball NTN open CN 183 162 6260
N224 Cylindrical Roller NTN open CN 288 320 5460
N224-ECP Cylindrical Roller SKF open CN 390 430 5750
NF224 Cylindrical Roller NTN open CN 288 320 5460
NJ224 Cylindrical Roller NTN open CN 288 320 5460
NJ224-ECP Cylindrical Roller SKF open CN 390 430 5850
NJ224E Cylindrical Roller NTN open CN 370 420 —
NU224 Cylindrical Roller NTN open CN 288 320 5460
NU224-ECP Cylindrical Roller SKF open CN 390 430 5750
NU224E Cylindrical Roller NTN open CN 370 420 —
NUP224 Cylindrical Roller NTN open CN 288 320 5460
NUP224-ECJ Cylindrical Roller SKF open CN 390 430 5950
NUP224E Cylindrical Roller NTN open CN 370 420 —
QJ-224-N2MA Angular Contact Ball SKF open CN 300 365 6950
QJ224 Angular Contact Ball NTN open CN 266 540 6750

Note: catalogue dynamic load ratings for this envelope span 146.0– 390.0 kN — a 167% spread between designs in the very same 120×215×40 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 120 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6224, 6224-2RS, 6224-2RS-NSK, 6224-2RS-NTN, 6224-M, 6224-NSK, 6224-NTN, 6224-RSR, 6224-ZZ, 6224-ZZ-NSK, 6224-ZZ-NTN, 7224, 7224-BCBM, 7224-BM, 7224B, N224, N224-ECP, NF224, NJ224, NJ224-ECP, NJ224E, NU224, NU224-ECP, NU224E, NUP224, NUP224-ECJ, NUP224E, QJ-224-N2MA, QJ224.

Frequently asked questions

Are all 120×215×40 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 120 mm bore, 215 mm OD, 40 mm width (4.724×8.465×1.575 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 29 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 120×215×40?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 120×215×40 mm in inches?

120×215×40 mm converts to 4.724×8.465×1.575 in, with a 47.5 mm (1.870 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6224, 6224-2RS, 6224-2RS-NSK mount in the same space despite different internal designs.