NJ2334-ECML bearing: complete specifications & equivalents
The NJ2334-ECML is a ISO 15 radial bearing sized 170 x 360 x 120 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 170 mm |
| Outer diameter D | 360 mm |
| Width B | 120 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 1450 kN |
| Basic static load rating C0 | 2040 kN |
| Fatigue load limit Pu | 204 kN |
| Reference speed (thermal) | 1700 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 60500 g |
| Manufacturer designation | SKF NJ 2334 ECML |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ2300-series range
| Bore d | 6.693 in |
|---|---|
| Outer diameter D | 14.173 in |
| Width B | 4.724 in |
| ISO bore code | 34 |
| Radial section height (D−d)/2 | 95 mm |
| Smallest bore in NJ2300-series | 20 mm |
| Largest outer diameter in NJ2300-series | 540 mm |
| Width range across NJ2300-series | 21–165 mm |
| Bore position in NJ2300-series (smallest first) | 24 of 28 |
| Bore above smallest NJ2300-series size | 150 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NU2334-ECML | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 170×360×120 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ2334-ECML model number is decoded
NJ2334-ECML is the 170 mm bore entry in the NJ2300 range: a 170×360×120 mm single-row caged cylindrical roller bearing with a one-piece machined brass cage, rated C 1450 kN / C0 2040 kN. Structurally, the NJ design has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set. In arrangement terms it is able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. Reading the order-string suffix ECML: the E-design ECML execution with a one-piece machined brass cage for higher-temperature, higher-speed continuous duty. With C 1450 kN and C0 2040 kN, size the bearing on the 170×360 mm ISO 15 envelope and check the 204 kN Pu against the equivalent-load floor; the catalogue lists 1,700 r/min thermal reference speed and 3,400 r/min mechanical limiting speed. Mounting: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. A 170 mm seat normally takes a m6 interference with an H6 housing bore when the inner ring rotates.
Typical equipment & failure modes
Common applications
- heavy turbogenerator rotor supports
- mining hoist and winder shafts
- offshore drawworks shafts
- large rolling-mill drive trains
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- edge loading from shaft deflection beyond the bearing alignment limit (≈ 3-4 minutes of arc for single-row CRB)
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 23 (medium-section, wide) envelope is shared with the N/NU/NJ/NUP executions of 2334, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 2334 ECML and do not substitute rib styles without checking the shaft locating scheme.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- Catalogue reference and limiting speeds are different criteria: observe the mechanical ceiling even when thermal calculations allow more.
- The 1450/2040 kN ratings are SKF catalogue 17000 (2018) values for the ECML execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ2334-ECML?
SKF NJ 2334 ECML is a single-row caged cylindrical roller bearing with 170 mm bore, 360 mm OD and 120 mm width per ISO 15. SKF lists C 1450 kN, C0 2040 kN, Pu 204 kN, reference speed 1,700 r/min and limiting speed 3,400 r/min, mass about 60500 g.
What does the NJ designation and ECML suffix mean?
The ECML suffix denotes the E-design execution with a one-piece machined brass cage for higher-temperature and higher-speed continuous duty. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ2334-ECML take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ2334-ECML compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.