NJ322-ECJ bearing: complete specifications & equivalents
The NJ322-ECJ is a ISO 15 radial bearing sized 110 x 240 x 50 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 110 mm |
| Outer diameter D | 240 mm |
| Width B | 50 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 530 kN |
| Basic static load rating C0 | 540 kN |
| Fatigue load limit Pu | 61 kN |
| Reference speed (thermal) | 3000 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 10500 g |
| Manufacturer designation | SKF NJ 322 ECJ |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NJ300-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 9.449 in |
| Width B | 1.969 in |
| ISO bore code | 22 |
| Radial section height (D−d)/2 | 65 mm |
| Smallest bore in NJ300-series | 17 mm |
| Largest outer diameter in NJ300-series | 500 mm |
| Width range across NJ300-series | 14–95 mm |
| Bore position in NJ300-series (smallest first) | 20 of 29 |
| Bore above smallest NJ300-series size | 93 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| N322-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 110×240×50 mm and equivalent catalogue ratings; the N execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NU322-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 110×240×50 mm and equivalent catalogue ratings; the NU execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
| NUP322-ECP | SKF | full Dimensions and internal design equivalent — standard interchange. | Same ISO 15 envelope 110×240×50 mm and equivalent catalogue ratings; the NUP execution differs in flange/retaining-ring configuration — boundary-dimension interchangeable, but axial-locating behaviour is not identical. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NJ322-ECJ model number is decoded
SKF NJ 322 ECJ is a single-row caged cylindrical roller bearing sized 110×240×50 mm — a dimension series 3 (medium-section ISO 15 envelope), listed in SKF catalogue PUB BU/P1 17000 ch. 6.1. The NJ configuration means two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set; functionally the bearing is able to locate the shaft axially in one direction; an HJ angle ring on the opposite side converts it into two-direction location. The ECJ suffix marks the E-design execution with a pressed sheet-steel window cage, useful where polymer cages are temperature- or lubricant-limited. Speed planning for NJ322-ECJ: the catalogue lists 3,000 r/min thermal reference speed and 3,400 r/min mechanical limiting speed. The mass entry 10500 g covers the complete catalogue execution. Fit practice for NJ322-ECJ: orient the inner-ring flange side toward the axial load direction; if an HJ angle ring is used, verify its fit and clearance before locking the arrangement. Single-row cylindrical rollers tolerate only about 3–4 minutes of arc misalignment, so verify shaft and housing alignment.
Typical equipment & failure modes
Common applications
- paper-machine press rolls
- cement-plant conveyor drives
- heavy gearbox and pinion shafts
- large pump and blower rotors
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- cage pocket wear from roller skew at light load
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- edge-loading fatigue after shaft deflection beyond the 3–4 minute alignment limit
- brinelling from static overload or impact during handling and mounting
Selection pitfalls — read before you substitute
- Do not use a NJ bearing where two-direction axial location is required without an HJ angle ring
- The dimension series 3 (medium-section ISO 15 envelope) envelope is shared with the N/NU/NJ/NUP executions of 322, but flange configuration and axial-locating behaviour differ — quote the full SKF NJ 322 ECJ and do not substitute rib styles without checking the shaft locating scheme.
- Press-fit force goes through ring faces only; driving a ring home through the rollers brinells the 240 mm raceway.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 50 mm-wide ring and concentrates load.
- The 530/540 kN ratings are SKF catalogue 17000 (2018) values for the ECJ execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NJ322-ECJ?
SKF NJ 322 ECJ is a single-row caged cylindrical roller bearing with 110 mm bore, 240 mm OD and 50 mm width per ISO 15. SKF lists C 530 kN, C0 540 kN, Pu 61 kN, reference speed 3,000 r/min and limiting speed 3,400 r/min, mass about 10500 g.
What does the NJ designation and ECJ suffix mean?
The ECJ suffix marks the E-design execution with a pressed sheet-steel window cage, useful where polymer cages are temperature- or lubricant-limited. Structurally this execution has two integral flanges on the inner ring and no flanges on the outer ring; the inner ring retains the roller set.
Can NJ322-ECJ take axial load and locate the shaft?
In one direction only, via the two inner-ring flanges. Add an HJ angle ring on the opposite side for two-direction location.
How does NJ322-ECJ compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.1 single-row cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.