NUH2322-ECMH bearing: complete specifications & equivalents
The NUH2322-ECMH is a ISO 15 radial bearing sized 110 x 240 x 80 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 110 mm |
| Outer diameter D | 240 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass |
| Basic dynamic load rating C | 830 kN |
| Basic static load rating C0 | 965 kN |
| Fatigue load limit Pu | 110 kN |
| Reference speed (thermal) | 3000 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 18000 g |
| Manufacturer designation | SKF NUH 2322 ECMH |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NUH2300-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 9.449 in |
| Width B | 3.15 in |
| ISO bore code | 22 |
| Radial section height (D−d)/2 | 65 mm |
| Smallest bore in NUH2300-series | 100 mm |
| Largest outer diameter in NUH2300-series | 500 mm |
| Width range across NUH2300-series | 73–155 mm |
| Bore position in NUH2300-series (smallest first) | 2 of 13 |
| Bore above smallest NUH2300-series size | 10 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NUH2322-ECMH model number is decoded
NUH2322-ECMH is the 110 mm bore entry in the NUH2300 range: a 110×240×80 mm high-capacity cylindrical roller bearing with a one-piece machined brass cage, rated C 830 kN / C0 965 kN. Reading the NUH prefix: a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring. This makes the execution the locating partner in paired cross-locating arrangements for heavily loaded shafts, locating axially in one direction. Reading the order-string suffix ECMH: the high-capacity execution with a machined brass cage (the /PEX variant is the pinion-shaft special build). Selection arithmetic: C0/C ≈ 1.16 (965 against 830 kN), and the Pu figure 110 kN is the fatigue load-limit floor for the SKF life equation; the catalogue lists 3,000 r/min thermal reference speed and 3,400 r/min mechanical limiting speed. Assembly note: typically paired with the matching NCF ECJB non-locating bearing on the same shaft; observe the catalogue shoulder and fillet data for the large inner ring. Heat steel rings inductively to max 120 °C. This is the standard catalogue execution of the high-capacity design. Selected sizes in the range are also produced as /PEX pinion-shaft builds for wind-turbine gearboxes — separate order numbers with their own rating lines and internal profiling; the two must not be mixed using one another’s loads.
Typical equipment & failure modes
Common applications
- wind-turbine rotor pinion shafts
- heavy mining and cement gear drives
- wind turbine gearbox planetary and intermediate shafts
Known failure patterns
- inner-ring raceway spalling from overload or contamination in the line-contact hertz zone
- outer-ring raceway fatigue after extended service at loads above the catalogue L10 rating
- micro-pitting on the profiled rollers under contaminated or starved-lubricant conditions despite the black-oxide treatment
- polymer cage cracking or softening after sustained running above 120 °C or with incompatible lubricant
- surface distress (micro-pitting) when the EHL film falls below the composite roughness at high specific load
- cage fatigue in heavily reversing wind-turbine load cycles when relubrication intervals are exceeded
- smearing (microwelding) on roller surfaces during skid starts with insufficient minimum load
Selection pitfalls — read before you substitute
- High-capacity NUH and NCF bearings are designed as a locating/non-locating PAIR on the same shaft; fitting two locating NUH bearings can preload the arrangement thermally.
- The /PEX pinion execution carries its own rating line and internal geometry — never substitute a standard NUH 2322 using the /PEX loads.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 80 mm-wide ring and concentrates load.
- Shaft and housing fillets must clear the bearing chamfers; an oversized radius tilts the 80 mm-wide ring and concentrates load.
- The 830/965 kN ratings are SKF catalogue 17000 (2018) values for the ECMH execution; re-verify against the current catalogue for critical drives and keep the catalogue version with the specification.
Frequently asked questions
What are the dimensions and catalogue data of NUH2322-ECMH?
SKF NUH 2322 ECMH is a high-capacity cylindrical roller bearing with 110 mm bore, 240 mm OD and 80 mm width per ISO 15. SKF lists C 830 kN, C0 965 kN, Pu 110 kN, reference speed 3,000 r/min and limiting speed 3,400 r/min, mass about 18000 g.
What does the NUH designation and ECMH suffix mean?
The ECMH suffix denotes the high-capacity execution with a machined brass cage; the /PEX variant is the pinion-shaft special build. Structurally this execution has a high-capacity NJ-type execution whose displaced cage bars make room for additional rollers, with two integral flanges on the inner ring.
Can NUH2322-ECMH take axial load and locate the shaft?
In one direction, as the locating member of a high-capacity pair; the matching NCF ECJB bearing floats. It is not a general-purpose axial bearing.
How does NUH2322-ECMH compare with the other executions in the same envelope?
The N/NU/NJ/NUP executions share the ISO 15 envelope and load ratings but differ in flange arrangement and axial-locating behaviour; quote the exact order number.
What limits the service life of this bearing most often?
Line-contact fatigue above the L10 rating, cage wear at light loads and high temperatures, and edge loading from misalignment beyond about 3–4 minutes of arc are the typical failure drivers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 6.2 high-capacity cylindrical roller bearings on 2026-09-26. Read our editorial & correction policy.