110×240×80 mm bearings

19 models from 3 brands across 2 types share this ISO 15 envelope: 110 mm bore, 240 mm outside diameter, 80 mm width (4.331×9.449×3.150 in), 65 mm radial section.

19 models fit this space 3 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22322 Spherical Roller SKF open CN 989 1120 18500
22322-EK Spherical Roller SKF open CN 989 1120 21000
22322EAD1 Spherical Roller NTN open CN 975 972 17000
22322EAKD1 Spherical Roller NTN open CN 975 972 16600
22322EMD1 Spherical Roller NTN open CN 975 972 17400
22322EMKD1 Spherical Roller NTN open CN 975 972 17100
N2322 Cylindrical Roller NTN open CN 670 790 16800
NJ2322 Cylindrical Roller NTN open CN 670 790 16800
NJ2322-ECP Cylindrical Roller SKF open CN 780 900 17000
NJ2322E Cylindrical Roller NTN open CN 750 880 —
NJG2322-VH Cylindrical Roller SKF open CN 858 1060 17500
NU2322 Cylindrical Roller NTN open CN 670 790 16800
NU2322-ECP Cylindrical Roller SKF open CN 780 900 17000
NU2322E Cylindrical Roller NTN open CN 750 880 —
NUH2322-ECMH Cylindrical Roller SKF open CN 830 965 18000
NUP2322 Cylindrical Roller NTN open CN 670 790 16800
NUP2322-ECP Cylindrical Roller SKF open CN 780 900 17500
NUP2322E Cylindrical Roller NTN open CN 750 880 —
SL192322-TB-XL-BR Cylindrical Roller FAG open CN 950 970 17000

Note: catalogue dynamic load ratings for this envelope span 670.0– 989.0 kN — a 48% spread between designs in the very same 110×240×80 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 110 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22322, 22322-EK, 22322EAD1, 22322EAKD1, 22322EMD1, 22322EMKD1, N2322, NJ2322, NJ2322-ECP, NJ2322E, NJG2322-VH, NU2322, NU2322-ECP, NU2322E, NUH2322-ECMH, NUP2322, NUP2322-ECP, NUP2322E, SL192322-TB-XL-BR.

Frequently asked questions

Are all 110×240×80 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 110 mm bore, 240 mm OD, 80 mm width (4.331×9.449×3.150 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 19 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 110×240×80?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 110×240×80 mm in inches?

110×240×80 mm converts to 4.331×9.449×3.150 in, with a 65 mm (2.559 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22322, 22322-EK, 22322EAD1 mount in the same space despite different internal designs.