HK2210 bearing: complete specifications & equivalents
The HK2210 is a ISO 3245 radial bearing sized 22 x 28 x 10 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 22 mm |
| Outer diameter D | 28 mm |
| Width B | 10 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 7.21 kN |
| Basic static load rating C0 | 10.6 kN |
| Fatigue load limit Pu | 1.2 kN |
| Reference speed (thermal) | 11000 rpm |
| Limiting speed (mechanical) | 12000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 13 g |
| Manufacturer designation | HK 2210 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.866 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.394 in |
| ISO bore code | 10 |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 17 of 26 |
| Bore above smallest HK-series size | 19 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the HK2210 model number is decoded
In SKF catalogue PUB BU/P1 17000, HK 2210 denotes a 22×28×10 mm drawn cup needle roller bearing with open ends — the shaft journal is the inner raceway, the pressed shell the outer, and the cage keeps the rollers parallel. Reading the code: HK marks the open-end drawn cup series, the first two digits (22) give the 22 mm under-roller diameter Fw, the last two (10) the 10 mm width; the 28 mm OD follows the ISO 3245 plan. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Drawn cups exist open (basic HK), sealed (2RS, with contact seals and grease fill) and with polymer TN cage; each is a separate order number with its own ratings, not a field conversion. For life calculation, the 7.21/10.6 kN ratings assume raceway geometry supplied by the shaft and housing in families without an inner ring — journal hardness, roundness and finish are part of the bearing, not of the application. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- auto steering gear rack supports
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- drawn-cup shell distortion or splitting from a careless press-in without a seating mandrel
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- false brinelling of standby equipment under external vibration
Selection pitfalls — read before you substitute
- On a 22 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 28 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Reference and limiting speeds are different limits: the 11,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 22 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The 7.21/10.6 kN ratings and 13 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What mounting mistakes ruin a HK 2210?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 2210 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Which dimensions does the HK 2210 have?
A HK 2210 measures 22 mm bore/Fw × 28 mm outside diameter × 10 mm width (0.866 × 1.102 × 0.394 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 7.21 kN, static C0 10.6 kN, fatigue limit Pu 1.2 kN, limiting speed 12,000 r/min, reference speed 11,000 r/min, mass about 13 g.
What does HK 2210 mean in SKF part numbering?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 22 mm, the last two the width 10 mm, the shell OD 28 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.