HK2212 bearing: complete specifications & equivalents
The HK2212 is a ISO 3245 radial bearing sized 22 x 28 x 12 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 22 mm |
| Outer diameter D | 28 mm |
| Width B | 12 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 8.8 kN |
| Basic static load rating C0 | 13.7 kN |
| Fatigue load limit Pu | 1.56 kN |
| Reference speed (thermal) | 11000 rpm |
| Limiting speed (mechanical) | 12000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 15 g |
| Manufacturer designation | HK 2212 |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.866 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.472 in |
| ISO bore code | 12 |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 17 of 26 |
| Bore above smallest HK-series size | 19 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK2212FM | NTN | full Dimensions and internal design equivalent — standard interchange. | NTN counterpart on the same 22×28×12 mm envelope with ratings within 10 % — interchange after checking the execution (cage/seal) details on both pages. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK2212 model number is decoded
Ordering number HK 2212 in SKF catalogue PUB BU/P1 17000 is an open-end HK drawn cup needle roller bearing: nominal code 22 for the 22 mm under-roller diameter and 12 for the 12 mm width. The designation HK 2212 encodes geometry only — there is no bore code to decode, since the 22 mm Fw is printed directly in the first digits and the cup width 12 mm in the last two. Open caged execution: the standard HK drawn cup with steel cage, relubricable through the shaft where the housing allows. Drawn cups exist open (basic HK), sealed (2RS, with contact seals and grease fill) and with polymer TN cage; each is a separate order number with its own ratings, not a field conversion. For life calculation, the 8.8/13.7 kN ratings assume raceway geometry supplied by the shaft and housing in families without an inner ring — journal hardness, roundness and finish are part of the bearing, not of the application. The shell is intentionally thin: seat it square with a slow press stroke, support the housing wall behind the bore, and stop the moment the cup face meets the shoulder — hammer blows split drawn cups.
Typical equipment & failure modes
Common applications
- auto steering gear rack supports
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- drawn-cup shell distortion or splitting from a careless press-in without a seating mandrel
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- false brinelling of standby equipment under external vibration
Selection pitfalls — read before you substitute
- On a 22 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 28 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- Do not interchange envelope-identical needle families blindly: HK 2212 shares its 22×28×12 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- The 8.8/13.7 kN ratings and 15 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does HK 2212 mean in SKF part numbering?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 22 mm, the last two the width 12 mm, the shell OD 28 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Does the HK 2212 need a hardened and ground shaft?
No. In this execution the 22 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 2212?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Is the HK 2212 sealed?
No — the open-end HK cup has no seals: the housing must keep contamination out and grease in. The 2RS execution of the same code adds both-side contact seals with a grease fill.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.