HK2216-2RS bearing: complete specifications & equivalents
The HK2216-2RS is a ISO 3245 radial bearing sized 22 x 28 x 16 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 22 mm |
| Outer diameter D | 28 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 8.8 kN |
| Basic static load rating C0 | 13.7 kN |
| Fatigue load limit Pu | 1.56 kN |
| Limiting speed (mechanical) | 7500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 18 g |
| Manufacturer designation | HK 2216.2RS |
| Standard | ISO 3245 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & HK-series range
| Bore d | 0.866 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.63 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 68 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 17 of 26 |
| Bore above smallest HK-series size | 19 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HK2216F | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | NTN bearing on the same 22×28×16 mm envelope, but catalogue C/C0 differ (8.8/13.7 vs 13.2/21.1 kN) — envelope interchange only after a load check. |
| HK2216 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 22×28×16 mm envelope, but catalogue C/C0 differ between the executions (8.8/13.7 vs 13/22.4 kN) — boundary dimensions match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HK2216-2RS model number is decoded
In SKF catalogue PUB BU/P1 17000, HK 2216.2RS denotes a 22×28×16 mm drawn cup needle roller bearing with open ends — the shaft journal is the inner raceway, the pressed shell the outer, and the cage keeps the rollers parallel. Reading the code: HK marks the open-end drawn cup series, the first two digits (22) give the 22 mm under-roller diameter Fw, the last two (16) the 16 mm width; the 28 mm OD follows the ISO 3245 plan. Sealed 2RS execution: rubber contact seals on both cup faces, factory grease fill, and the slightly lower ratings of a sealed drawn cup — 8.8 kN C against the open bearing of the same code. Caged HK bearings space the rollers for lower friction than full complement HK types; the cage is not a seal — 2RS executions are the sealed members of the family. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. Mounting: press the cup in with a shouldered mandrel against the stamped end face only — through-the-rollers pressing brinells both raceways; the housing bore takes a firm press fit and the shaft slides in after.
Typical equipment & failure modes
Common applications
- clutch release mechanisms and cable pulleys
- office equipment and power tool gear trains
- steering column and pedal-box pivots in passenger cars
- idler gears and pulleys in small appliance drives
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- fretting corrosion of the cup outside diameter in a soft or oversized housing bore
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- corrosion pitting from condensation in intermittently operated machinery
Selection pitfalls — read before you substitute
- On a 22 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 28 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- The quoted 8.8/13.7 kN ratings are SKF catalogue values for this exact execution (HK 2216.2RS); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 8.8/13.7 kN ratings and 18 g mass are SKF catalogue values transcribed from ch. 7.2 of PUB BU/P1 17000 (PDF table page 622); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Which dimensions does the HK 2216.2RS have?
A HK 2216.2RS measures 22 mm bore/Fw × 28 mm outside diameter × 16 mm width (0.866 × 1.102 × 0.63 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 8.8 kN, static C0 13.7 kN, fatigue limit Pu 1.56 kN, limiting speed 7,500 r/min, mass about 18 g.
What does HK 2216.2RS mean in SKF part numbering?
HK = open-end drawn cup needle roller bearing (ISO 3245); the first two digits give Fw 22 mm, the last two the width 16 mm, the shell OD 28 mm follows the plan. 2RS adds both-side contact seals, TN the polymer cage.
Does the HK 2216.2RS need a hardened and ground shaft?
No. In this execution the 22 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a HK 2216.2RS?
Press the cup in with a shouldered mandrel bearing on the stamped face, into a housing bore sized for a firm press fit; never hammer it or press through the rollers. Then slide the hardened shaft in. For 2RS executions the seals and grease are already in place — no additional sealing is needed.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.2 drawn cup needle roller bearings on 2026-09-26. Read our editorial & correction policy.