HK2216F bearing: complete specifications & equivalents
The HK2216F is a ISO 3245 radial bearing sized 22 x 28 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 22 mm |
| Outer diameter D | 28 mm |
| Width B | 16 mm |
| Seal / shield | open |
| Basic dynamic load rating C | 13.2 kN |
| Basic static load rating C0 | 21.1 kN |
| Fatigue load limit Pu | 2.57 kN |
| Limiting speed (mechanical) | 7500 rpm |
| Mass | 21 g |
| Manufacturer designation | HK2216F |
| Standard | ISO 3245 |
| Catalog version | CAT. No. 2203-3/E 2024 |
| Last verified | 2026-09-25 |
Source: catalog reference (CAT. No. 2203-3/E 2024) · extracted 2026-09-25
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (CAT. No. 2203-3/E 2024); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & HK-series range
| Bore d | 0.866 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.63 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 3 mm |
| Smallest bore in HK-series | 3 mm |
| Largest outer diameter in HK-series | 58 mm |
| Width range across HK-series | 6–38 mm |
| Bore position in HK-series (smallest first) | 17 of 24 |
| Bore above smallest HK-series size | 19 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the HK2216F model number is decoded
HK2216F is an NTN drawn-cup needle roller bearing with open ends in the HK-series (ISO 3245 boundary dimensions).The designation encodes the shaft fit directly: Fw = 22 mm is the under-roller diameter, i.e. the shaft journal that serves as the inner raceway; the cup outside diameter is 28 mm and the width is 16 mm. There is no separate inner ring — the thin-walled cup is drawn from sheet steel, hardened, and press-fitted into the housing, giving the smallest radial section of any rolling bearing at this shaft size. The F suffix marks NTN's caged drawn-cup execution: a formed steel cage spaces the rollers, lowering friction versus full-complement drawn cups. Mid-size drawn cups like this appear throughout passenger-car and light-truck transmissions, pressed into cast housings where a machined ring would not fit. This size is specified in printing-press folder and cutter mechanisms, where the shaft is short, the loads are cyclical, and the thin cup lets the frame plates stay close together. When replacing this size, measure the housing bore with a plug gauge before pressing the new cup: a bore worn oversize by the previous bearing will not retain the new shell.
Typical equipment & failure modes
Common applications
- universal joint and steering pivots
- automotive manual transmission gear sets
- industrial gearbox lay shafts
- intermittent duty with long standstill periods that invite false brinelling
Known failure patterns
- brinelling of the drawn cup from hammer blows during press-in mounting
- grease starvation in the open-end arrangement with no relubrication path
- raceway spalling on a shaft that was below the required 58–64 HRC hardness
Selection pitfalls — read before you substitute
- The open ends of HK2216F retain no lubricant: grease must be supplied by the housing arrangement, and adjacent seals are needed in dirty or washdown duty.
- Mid-size cups like HK2216F (22 mm shaft) inherit the shape of their seat: a scored or oval housing bore from the previous bearing will cut the new bearing's life short.
- The cage in HK2216F guides the rollers but is not a seal: it retains nothing against dust or washdown, so the housing still needs its own sealing arrangement at 22 mm.
- The 16 mm standard width of HK2216F is the general-purpose section at 22 mm shaft; wider HK variants in the same 22×28 mm envelope carry more load and are not interchangeable if the housing width is fixed.
Frequently asked questions
Does HK2216F need a hardened shaft?
Either the 22 mm shaft journal must be hardened to 58–64 HRC and ground to Ra ≤ 0.2 µm, or you can fit the matching inner ring (IR17x22x18) so a standard unhardened shaft can be used.
What are the dimensions of a HK2216F needle roller bearing?
A HK2216F drawn-cup needle roller bearing has a 22 mm shaft diameter (Fw, under-roller diameter), 28 mm outside diameter and 16 mm width, per ISO 3245 boundary dimensions. It has no inner ring — the shaft journal serves as the raceway.
What does Fw mean on a HK2216F drawn-cup bearing?
Fw is the under-roller diameter — the diameter of the shaft journal on which the needle rollers run directly. For HK2216F, Fw = 22 mm, so the shaft must be machined to 22 mm, hardened to 58–64 HRC and ground, unless a separate IR inner ring is fitted.
Can a HK2216F needle roller bearing carry axial load?
No. Drawn-cup needle roller bearings like HK2216F carry radial load only and provide no axial shaft location. Axial forces must be carried by separate thrust washers or a locating bearing in the arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog CAT. No. 2203-3/E 2024 on 2026-09-25. Read our editorial & correction policy.