NA4900 bearing: complete specifications & equivalents
The NA4900 is a ISO 1206 radial bearing sized 10 x 22 x 13 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 22 mm |
| Width B | 13 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 8.8 kN |
| Basic static load rating C0 | 10.4 kN |
| Fatigue load limit Pu | 1.22 kN |
| Reference speed (thermal) | 24000 rpm |
| Limiting speed (mechanical) | 28000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 24 g |
| Manufacturer designation | NA 4900 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NA-49-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 0.866 in |
| Width B | 0.512 in |
| ISO bore code | 00 |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in NA-49-series | 10 mm |
| Largest outer diameter in NA-49-series | 190 mm |
| Width range across NA-49-series | 13–50 mm |
| Bore position in NA-49-series (smallest first) | 1 of 28 |
| Bore above smallest NA-49-series size | 0 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NA4900 model number is decoded
For a 10 mm shaft that cannot be hardened on site, NA 4900 adds a hardened, ground inner ring to the machined needle roller design: envelope 10×22×13 mm per the dimension series 49 needle roller bearings with inner ring plan. Reading the designation: the letters name the series with inner ring, the numbers the boundary plan — 10 mm bore (d), 13 mm width; the 22 mm OD follows the dimension series, and the inner ring is a separate ground component. TN polymer cage executions run quieter and tolerate grease-lubricated pivot duty; steel cage executions remain the choice for higher temperature or oil-bath lubrication. Catalogue mass 24 g at 10×22×13 mm makes this one of the highest capacity-per-gram choices in the dimension series 49 needle roller bearings with inner ring; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Because the inner ring is separable, mount it first against its shoulder, then slide the outer ring and roller set over it — the order avoids forcing rollers across the shaft threads or burrs.
Typical equipment & failure modes
Common applications
- printing and paper-handling rollers
- gearbox shafts where the journal cannot be hardened on site
- wheel and lever pivots needing a replaceable inner ring
- conveyor roller ends and return rollers
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- cage pocket wear and roller skew after sustained operation with too little radial preload
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- false brinelling of standby equipment under external vibration
- inner-ring raceway spalling after the narrow ring section runs hot with excessive interference
Selection pitfalls — read before you substitute
- On a 10 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 22 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- Do not interchange envelope-identical needle families blindly: NA 4900 shares its 10×22×13 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- The 8.8/10.4 kN ratings and 24 g mass are SKF catalogue values transcribed from ch. 7.4 of PUB BU/P1 17000 (PDF table page 638); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does NA 4900 mean in SKF part numbering?
The letters mark a machined-ring needle roller bearing with inner ring: 10 mm bore, 13 mm width, 22 mm OD per the series plan. The hardened inner ring is the raceway, so an ordinary k5 shaft seat suffices.
Does the NA 4900 need a hardened and ground shaft?
Yes — that is the point of this family. The NA 4900 carries its own hardened, ground inner ring on a 10 mm seat, so the shaft needs only a normal k5/j6 finish. The inner ring is separable and replaceable.
What mounting mistakes ruin a NA 4900?
Mount the inner ring on the 10 mm seat first (induction heat, max 120 °C, or press), then fit the flanged outer ring into the H7 housing bore. Verify free rotation and, for 2RS executions, check the wider outer ring against the housing depth.
Is the NA 4900 sealed?
No — the open execution relies on housing seals; 2RS executions of the 49 series add contact seals with a wider outer ring as a separate order number.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring on 2026-09-26. Read our editorial & correction policy.