22230EAD1 bearing: complete specifications & equivalents
The 22230EAD1 is a ISO 15 radial bearing sized 150 x 270 x 73 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 150 mm |
| Outer diameter D | 270 mm |
| Width B | 73 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1080 kN |
| Basic static load rating C0 | 1220 kN |
| Fatigue load limit Pu | 74.4 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 17600 g |
| Manufacturer designation | NTN 22230EAD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22200-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 10.63 in |
| Width B | 2.874 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 580 mm |
| Width range across 22200-series | 18–150 mm |
| Bore position in 22200-series (smallest first) | 21 of 32 |
| Bore above smallest 22200-series size | 125 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22230EAKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22200-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 22230EAKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22230EAD1 model number is decoded
22230EAD1 is the EA pressed-steel-cage execution of NTN's spherical roller range for a 150 mm shaft — 1080 kN basic dynamic capacity in a 17600 g, open ISO 15 envelope. Digit by digit the code reads as spherical-roller dimension series plus 150 mm bore; the 73 mm width is the wide ISO 15 section, which is why spherical rollers interchange dimensionally but not in cage or rating detail. Pu 74.4 kN is the catalogue fatigue load limit for 22230EAD1, used in the adjusted-life equation at contaminated or partial-film conditions typical of mining and vibrating duty. Equivalent-load planning keeps a radial plus moderate axial combination on 22230EAD1; if the axial component dominates, pair with a thrust bearing rather than running one roller row unloaded. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 22230EAD1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
- cement-rotary-kiln support and trunnion rolls
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- brinelling from static overload or a hammer blow during sleeve mounting
- rolling-contact fatigue after the catalogue L10 life at the actual load
Selection pitfalls — read before you substitute
- At 150 mm bore 22230EAD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 150 mm bearing, and drive-up procedures differ.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,800 r/min grease rating is lost to abrasive wear long before fatigue.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 22230EAD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 22230EAD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- The 1080/1220 kN ratings, 74.4 kN Pu and 17600 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22230EAD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22230EAD1?
22230EAD1 is an NTN double-row spherical roller bearing to ISO 15: 150 mm bore, 270 mm OD and 73 mm width (5.906 × 10.63 × 2.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1080 kN, C0 1220 kN, Pu 74.4 kN, grease limiting speed 1,800 r/min, oil 2,300 r/min, mass about 17600 g. It is open, with pressed sheet-steel window cage (EA high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
22230EAD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 22230EAKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22230EAD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22230EAD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22230EAD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22230EAD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22200 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1080 kN C / 1220 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.