22230EAKD1 bearing: complete specifications & equivalents
The 22230EAKD1 is a ISO 15 radial bearing sized 150 x 270 x 73 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 150 mm |
| Outer diameter D | 270 mm |
| Width B | 73 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1080 kN |
| Basic static load rating C0 | 1220 kN |
| Fatigue load limit Pu | 74.4 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 17300 g |
| Manufacturer designation | NTN 22230EAKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22200-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 10.63 in |
| Width B | 2.874 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 580 mm |
| Width range across 22200-series | 18–150 mm |
| Bore position in 22200-series (smallest first) | 21 of 32 |
| Bore above smallest 22200-series size | 125 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22230EAD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22200-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 22230EAD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22230EAKD1 model number is decoded
22230EAKD1 is the EA pressed-steel-cage execution of NTN's spherical roller range for a 150 mm shaft — 1080 kN basic dynamic capacity in a 17300 g, open ISO 15 envelope. On the NTN nameplate the suffix cluster after the size reads in order: cage design (EA), bore (K), lubrication feature (D1); 22230EAKD1 is assembled exactly in that order. Pu 74.4 kN is the catalogue fatigue load limit for 22230EAKD1, used in the adjusted-life equation at contaminated or partial-film conditions typical of mining and vibrating duty. Speed planning: 1,800 r/min grease limiting speed is the cage/kinematic ceiling and 2,300 r/min is the oil-lubricated value for the 150 mm bore; vibrating screens rarely approach either and are load/cage limited instead. Mount 22230EAKD1 on its adapter or withdrawal sleeve on the 150 mm plain shaft: oil the sleeve, fit the lock nut, drive up to the NTN-specified residual clearance (or use oil injection on large seats), then lock the tab washer.
Typical equipment & failure modes
Common applications
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- rolling-contact fatigue after the catalogue L10 life at the actual load
- hard-particle indentation through the open arrangement in dusty mining duty
Selection pitfalls — read before you substitute
- At 150 mm bore 22230EAKD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Self-aligning does not mean unlimited misalignment: beyond the catalogue angle the outer ring's spherical travel is exhausted and the 1080 kN rating no longer applies.
- Oil relubrication toward 2,300 r/min needs drain and level design; flooding the 73 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,800 r/min grease rating is lost to abrasive wear long before fatigue.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 22230EAKD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- The 1080/1220 kN ratings, 74.4 kN Pu and 17300 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22230EAKD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22230EAKD1?
22230EAKD1 is an NTN double-row spherical roller bearing to ISO 15: 150 mm bore, 270 mm OD and 73 mm width (5.906 × 10.63 × 2.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1080 kN, C0 1220 kN, Pu 74.4 kN, grease limiting speed 1,800 r/min, oil 2,300 r/min, mass about 17300 g. It is open, with pressed sheet-steel window cage (EA high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 22230EAKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 22230EAD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22230EAKD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22230EAKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22230EAKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22230EAKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22200 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1080 kN C / 1220 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.