22319EAKD1 bearing: complete specifications & equivalents
The 22319EAKD1 is a ISO 15 radial bearing sized 95 x 200 x 67 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 95 mm |
| Outer diameter D | 200 mm |
| Width B | 67 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 732 kN |
| Basic static load rating C0 | 751 kN |
| Fatigue load limit Pu | 43.4 kN |
| Limiting speed (mechanical) | 2300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 9710 g |
| Manufacturer designation | NTN 22319EAKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22300-series range
| Bore d | 3.74 in |
|---|---|
| Outer diameter D | 7.874 in |
| Width B | 2.638 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 52.5 mm |
| Smallest bore in 22300-series | 40 mm |
| Largest outer diameter in 22300-series | 620 mm |
| Width range across 22300-series | 33–185 mm |
| Bore position in 22300-series (smallest first) | 12 of 28 |
| Bore above smallest 22300-series size | 55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22319EAD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22300-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 22319EAD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22319EAKD1 model number is decoded
For heavy radial load with misalignment on a 95 mm shaft, NTN supplies 22319EAKD1: sphered outer raceway, two roller rows, pressed sheet-steel window cage (EA high-capacity design), oil speed 2,800 r/min. On the NTN nameplate the suffix cluster after the size reads in order: cage design (EA), bore (K), lubrication feature (D1); 22319EAKD1 is assembled exactly in that order. At 732 kN C and 9710 g mass the 22300 series part is built for shock and vibration; the 67 mm-wide ring needs square abutments to keep both rows equally loaded. The 52.5 mm section height hosts the spherical roller geometry; shaft and housing fillet radii must clear the chamfer table so the 67 mm-wide ring seats fully on both sides. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- wind-turbine gearbox and rotor bearings
- large vibrating screens and mining feeders
- heavy conveyor and bucket-excavator pulleys
- jaw/cone crusher eccentric and shaft positions
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- micro-pitting when the EHL film is thinner than the raceway composite roughness
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- water-induced pitting in washdown or outdoor duty without effective external seals
Selection pitfalls — read before you substitute
- Mount the 95 mm ring with induction heat or the sleeve drive-up procedure; at 9710 g cocking damages the spherical raceways, and repositioning after seating is impractical.
- Never substitute 22319EAKD1 by envelope alone: the 751 kN C0 and 43.4 kN Pu are specific to the NTN EA pressed-steel-cage execution, and vibrating duty depends heavily on cage identity.
- Oil relubrication toward 2,800 r/min needs drain and level design; flooding the 67 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Do not confuse EA and EM at the same number: 22319EAKD1 carries EA pressed-steel-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 95×200 mm envelope is identical.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 2,300 r/min grease rating is lost to abrasive wear long before fatigue.
- The 732/751 kN ratings, 43.4 kN Pu and 9710 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22319EAKD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22319EAKD1?
22319EAKD1 is an NTN double-row spherical roller bearing to ISO 15: 95 mm bore, 200 mm OD and 67 mm width (3.74 × 7.874 × 2.638 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 732 kN, C0 751 kN, Pu 43.4 kN, grease limiting speed 2,300 r/min, oil 2,800 r/min, mass about 9710 g. It is open, with pressed sheet-steel window cage (EA high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 22319EAKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 22319EAD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22319EAKD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22319EAKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22319EAKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22319EAKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22300 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 732 kN C / 751 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.