MPNbase

95×200×67 mm bearings

23 models from 3 brands across 4 types share this ISO 15 envelope: 95 mm bore, 200 mm outside diameter, 67 mm width (3.740×7.874×2.638 in), 52.5 mm radial section.

23 models fit this space 3 brands 23 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22319 Spherical Roller SKF open CN 699 765 10500
22319-EK Spherical Roller SKF open CN 699 765 12000
22319EAD1 Spherical Roller NTN open CN 732 751 9910
22319EAKD1 Spherical Roller NTN open CN 732 751 9710
22319EMD1 Spherical Roller NTN open CN 732 751 10000
22319EMKD1 Spherical Roller NTN open CN 732 751 9820
2319 Self-Aligning Ball NTN open — 161 64.5 8970
2319-KM Self-Aligning Ball SKF open CN 165 64 9800
2319-M Self-Aligning Ball SKF open CN 165 64 9800
2319K Self-Aligning Ball NTN open — 161 64.5 8970
C2319 CARB Toroidal Roller SKF open CN 610 695 10000
C2319-K CARB Toroidal Roller SKF open CN 610 695 10000
N2319 Cylindrical Roller NTN open CN 410 460 9020
NJ2319 Cylindrical Roller NTN open CN 410 460 9020
NJ2319-ECJ Cylindrical Roller SKF open CN 530 585 9550
NJ2319E Cylindrical Roller NTN open CN 510 585 —
NU2319 Cylindrical Roller NTN open CN 410 460 9020
NU2319-ECP Cylindrical Roller SKF open CN 530 585 9350
NU2319E Cylindrical Roller NTN open CN 510 585 —
NUP2319 Cylindrical Roller NTN open CN 410 460 9020
NUP2319-ECJ Cylindrical Roller SKF open CN 530 585 9700
NUP2319E Cylindrical Roller NTN open CN 510 585 —
SL192319-TB-XL Cylindrical Roller FAG open CN 650 710 10200

Note: catalogue dynamic load ratings for this envelope span 161.0– 732.0 kN — a 355% spread between designs in the very same 95×200×67 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 95 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22319, 22319-EK, 22319EAD1, 22319EAKD1, 22319EMD1, 22319EMKD1, 2319, 2319-KM, 2319-M, 2319K, C2319, C2319-K, N2319, NJ2319, NJ2319-ECJ, NJ2319E, NU2319, NU2319-ECP, NU2319E, NUP2319, NUP2319-ECJ, NUP2319E, SL192319-TB-XL.

Frequently asked questions

Are all 95×200×67 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 95 mm bore, 200 mm OD, 67 mm width (3.740×7.874×2.638 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 23 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 95×200×67?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 95×200×67 mm in inches?

95×200×67 mm converts to 3.740×7.874×2.638 in, with a 52.5 mm (2.067 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22319, 22319-EK, 22319EAD1 mount in the same space despite different internal designs.