22319EMD1 bearing: complete specifications & equivalents
The 22319EMD1 is a ISO 15 radial bearing sized 95 x 200 x 67 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 95 mm |
| Outer diameter D | 200 mm |
| Width B | 67 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 732 kN |
| Basic static load rating C0 | 751 kN |
| Fatigue load limit Pu | 43.4 kN |
| Limiting speed (mechanical) | 2300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 10000 g |
| Manufacturer designation | NTN 22319EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22300-series range
| Bore d | 3.74 in |
|---|---|
| Outer diameter D | 7.874 in |
| Width B | 2.638 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 52.5 mm |
| Smallest bore in 22300-series | 40 mm |
| Largest outer diameter in 22300-series | 620 mm |
| Width range across 22300-series | 33–185 mm |
| Bore position in 22300-series (smallest first) | 12 of 28 |
| Bore above smallest 22300-series size | 55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22319EMKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22300-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 22319EMKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22319EMD1 model number is decoded
The NTN order number 22319EMD1 identifies a 95×200×67 mm (3.74 × 7.874 × 2.638 in) spherical roller bearing, cylindrical bore, to the ISO 15 boundary plan. The leading digits are the ISO 15 dimension series (22300 series); the bore code resolves to 95 mm (two-digit code ×5, with the 00–03 exception table), and 200 mm OD / 67 mm width follow the general plan. The cylindrical bore fits a machined 95 mm shaft seat directly; the same envelope in 22319EMKD1 (tapered) is the sleeve-mounted alternative when clearance must be set by drive-up. 95 mm bore is 3.74 in and 200 mm OD is 7.874 in; the ISO 15 envelope swaps between brands, but the 732/751 kN ratings and cage design are NTN 2203E values. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 22319EMD1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- cement-mill and kiln auxiliary drives
- large gearbox and marine gear shafts
- wind-turbine gearbox and rotor bearings
- large vibrating screens and mining feeders
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- pressed EA cage fatigue under sustained vibration when minimum load is not maintained
- roller-end smearing during skidding starts under light load and high viscosity grease
- asymmetric wear on the two roller rows from sustained angular misalignment beyond the self-aligning range
- false brinelling on stopped machines exposed to screen or crusher vibration
Selection pitfalls — read before you substitute
- Mount the 95 mm ring with induction heat or the sleeve drive-up procedure; at 10000 g cocking damages the spherical raceways, and repositioning after seating is impractical.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 67 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 67 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- Minimum load must be maintained even at rest under vibration: an unloaded 22319EMD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- Do not confuse EA and EM at the same number: 22319EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 95×200 mm envelope is identical.
- The 732/751 kN ratings, 43.4 kN Pu and 10000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22319EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22319EMD1?
22319EMD1 is an NTN double-row spherical roller bearing to ISO 15: 95 mm bore, 200 mm OD and 67 mm width (3.74 × 7.874 × 2.638 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 732 kN, C0 751 kN, Pu 43.4 kN, grease limiting speed 2,300 r/min, oil 2,800 r/min, mass about 10000 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
22319EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 22319EMKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22319EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22319EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22319EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22319EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22300 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 732 kN C / 751 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.