23134EAD1 bearing: complete specifications & equivalents
The 23134EAD1 is a ISO 15 radial bearing sized 170 x 280 x 88 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 170 mm |
| Outer diameter D | 280 mm |
| Width B | 88 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1270 kN |
| Basic static load rating C0 | 1700 kN |
| Fatigue load limit Pu | 77.3 kN |
| Limiting speed (mechanical) | 1400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 21500 g |
| Manufacturer designation | NTN 23134EAD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 6.693 in |
|---|---|
| Outer diameter D | 11.024 in |
| Width B | 3.465 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 55 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 8 of 36 |
| Bore above smallest 23100-series size | 70 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23134EAKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23134EAKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23134EAD1 model number is decoded
23134EAD1 belongs to the 23100 series of NTN spherical rollers and carries the ＊ ULTAGE new-generation mark in the 2203E table: self-aligning, high radial capacity, moderate axial load in either direction. The leading digits are the ISO 15 dimension series (23100 series); the bore code resolves to 170 mm (two-digit code ×5, with the 00–03 exception table), and 280 mm OD / 88 mm width follow the general plan. Open by design, 23134EAD1 requires application seals and a grease or oil system; NTN vibrating-duty executions of this envelope are selected with cage and clearance choices that are separate order codes. Selection: the C0/C ratio of 1.34 (1700/1270 kN) reflects the heavy static and shock proportioning of 23134EAD1; size the equivalent load at the required L10 with shock factor for the application. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 23134EAD1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- water-induced pitting in washdown or outdoor duty without effective external seals
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
Selection pitfalls — read before you substitute
- At 170 mm bore 23134EAD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- The cylindrical-bore 23134EAD1 and its tapered-bore counterpart 23134EAKD1 share envelope and ratings but not mounting: do not order the K variant unless the drawing specifies a sleeve or tapered seat.
- Minimum load must be maintained even at rest under vibration: an unloaded 23134EAD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- Do not confuse EA and EM at the same number: 23134EAD1 carries EA pressed-steel-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 170×280 mm envelope is identical.
- Self-aligning does not mean unlimited misalignment: beyond the catalogue angle the outer ring's spherical travel is exhausted and the 1270 kN rating no longer applies.
- The 1270/1700 kN ratings, 77.3 kN Pu and 21500 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23134EAD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23134EAD1?
23134EAD1 is an NTN double-row spherical roller bearing to ISO 15: 170 mm bore, 280 mm OD and 88 mm width (6.693 × 11.024 × 3.465 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1270 kN, C0 1700 kN, Pu 77.3 kN, grease limiting speed 1,400 r/min, oil 1,800 r/min, mass about 21500 g. It is open, with pressed sheet-steel window cage (EA high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23134EAD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23134EAKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23134EAD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23134EAD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23134EAD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23134EAD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1270 kN C / 1700 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.