MPNbase

100×215×73 mm bearings

24 models from 3 brands across 4 types share this ISO 15 envelope: 100 mm bore, 215 mm outside diameter, 73 mm width (3.937×8.465×2.874 in), 57.5 mm radial section.

24 models fit this space 3 brands 24 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22320 Spherical Roller SKF open CN 847 950 13500
22320-EK Spherical Roller SKF open CN 847 950 15000
22320EAD1 Spherical Roller NTN open CN 827 844 12600
22320EAKD1 Spherical Roller NTN open CN 827 844 12300
22320EMD1 Spherical Roller NTN open CN 827 844 12900
22320EMKD1 Spherical Roller NTN open CN 827 844 12700
2320 Self-Aligning Ball NTN open — 187 79 11500
2320-K Self-Aligning Ball SKF open CN 190 80 12500
2320K Self-Aligning Ball NTN open — 187 79 11500
C2320 CARB Toroidal Roller SKF open CN 800 880 12500
C2320-K CARB Toroidal Roller SKF open CN 800 880 12500
N2320 Cylindrical Roller NTN open CN 455 505 11500
NJ2320 Cylindrical Roller NTN open CN 455 505 11500
NJ2320-ECJ Cylindrical Roller SKF open CN 670 735 12000
NJ2320E Cylindrical Roller NTN open CN 630 715 —
NJG2320-VH Cylindrical Roller SKF open CN 704 900 13000
NU2320 Cylindrical Roller NTN open CN 455 505 11500
NU2320-ECP Cylindrical Roller SKF open CN 670 735 12000
NU2320E Cylindrical Roller NTN open CN 630 715 —
NUH2320-ECMH Cylindrical Roller SKF open CN 710 800 13000
NUP2320 Cylindrical Roller NTN open CN 455 505 11500
NUP2320-ECJ Cylindrical Roller SKF open CN 670 735 12500
NUP2320E Cylindrical Roller NTN open CN 630 715 —
SL192320-TB-XL-BR Cylindrical Roller FAG open CN 790 850 13000

Note: catalogue dynamic load ratings for this envelope span 187.0– 847.0 kN — a 353% spread between designs in the very same 100×215×73 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 100 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22320, 22320-EK, 22320EAD1, 22320EAKD1, 22320EMD1, 22320EMKD1, 2320, 2320-K, 2320K, C2320, C2320-K, N2320, NJ2320, NJ2320-ECJ, NJ2320E, NJG2320-VH, NU2320, NU2320-ECP, NU2320E, NUH2320-ECMH, NUP2320, NUP2320-ECJ, NUP2320E, SL192320-TB-XL-BR.

Frequently asked questions

Are all 100×215×73 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 100 mm bore, 215 mm OD, 73 mm width (3.937×8.465×2.874 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 24 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 100×215×73?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 100×215×73 mm in inches?

100×215×73 mm converts to 3.937×8.465×2.874 in, with a 57.5 mm (2.264 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22320, 22320-EK, 22320EAD1 mount in the same space despite different internal designs.