170×310×86 mm bearings

17 models from 3 brands across 3 types share this ISO 15 envelope: 170 mm bore, 310 mm outside diameter, 86 mm width (6.693×12.205×3.386 in), 70 mm radial section.

17 models fit this space 3 brands 17 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22234EMD1 Spherical Roller NTN open CN 1400 1610 28300
22234EMKD1 Spherical Roller NTN open CN 1400 1610 27700
C2234 CARB Toroidal Roller SKF open CN 1270 1630 28000
C2234-K CARB Toroidal Roller SKF open CN 1270 1630 28000
N2234 Cylindrical Roller NTN open CN 795 1080 26700
NCF2234-ECJB Cylindrical Roller SKF open CN 1160 1530 28000
NCF2234-V Cylindrical Roller SKF open CN 1100 1700 28500
NJ2234 Cylindrical Roller NTN open CN 795 1080 26700
NJ2234-ECML Cylindrical Roller SKF open CN 1060 1340 29000
NJ2234E Cylindrical Roller NTN open CN 1070 1410 —
NU2234 Cylindrical Roller NTN open CN 795 1080 26700
NU2234-ECML Cylindrical Roller SKF open CN 1060 1340 28000
NU2234E Cylindrical Roller NTN open CN 1070 1410 —
NUH2234-ECMH Cylindrical Roller SKF open CN 1600 1530 28500
NUP2234 Cylindrical Roller NTN open CN 795 1080 26700
NUP2234E Cylindrical Roller NTN open CN 1070 1410 —
SL182234 Cylindrical Roller FAG open CN 1140 1660 28650

Note: catalogue dynamic load ratings for this envelope span 795.0– 1600.0 kN — a 101% spread between designs in the very same 170×310×86 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 170 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22234EMD1, 22234EMKD1, C2234, C2234-K, N2234, NCF2234-ECJB, NCF2234-V, NJ2234, NJ2234-ECML, NJ2234E, NU2234, NU2234-ECML, NU2234E, NUH2234-ECMH, NUP2234, NUP2234E, SL182234.

Frequently asked questions

Are all 170×310×86 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 170 mm bore, 310 mm OD, 86 mm width (6.693×12.205×3.386 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 17 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 170×310×86?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 170×310×86 mm in inches?

170×310×86 mm converts to 6.693×12.205×3.386 in, with a 70 mm (2.756 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22234EMD1, 22234EMKD1, C2234 mount in the same space despite different internal designs.