MPNbase

75×115×20 mm bearings

20 models from 4 brands across 3 types share this ISO 15 envelope: 75 mm bore, 115 mm outside diameter, 20 mm width (2.953×4.528×0.787 in), 20 mm radial section.

20 models fit this space 4 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6015 Deep Groove Ball SKF open CN 41.6 33.5 650
6015-2RS Deep Groove Ball SKF 2RS CN 41.6 33.5 670
6015-2RS-NSK Deep Groove Ball NSK 2RS CN 43.5 33.5 649
6015-2RS-NTN Deep Groove Ball NTN 2RS CN 44 33.5 649
6015-M Deep Groove Ball SKF open CN 41.6 33.5 740
6015-NSK Deep Groove Ball NSK open CN 43.5 33.5 649
6015-NTN Deep Groove Ball NTN open CN 44 33.5 649
6015-RSR Deep Groove Ball SKF RSR CN 41.6 33.5 670
6015-RSR-NSK Deep Groove Ball NSK RSR CN 43.5 33.5 649
6015-RSR-NTN Deep Groove Ball NTN RSR CN 44 33.5 649
6015-ZZ Deep Groove Ball SKF ZZ CN 41.6 33.5 680
6015-ZZ-NSK Deep Groove Ball NSK ZZ CN 43.5 33.5 649
6015-ZZ-NTN Deep Groove Ball NTN ZZ CN 44 33.5 649
7015 Angular Contact Ball GENERIC-ISO open CN — — 609
7015-NTN Angular Contact Ball NTN open CN 48.5 41.5 745
N1015 Cylindrical Roller NTN open CN 66.5 74.5 727
NJ1015 Cylindrical Roller NTN open CN 66.5 74.5 727
NU1015 Cylindrical Roller NTN open CN 66.5 74.5 727
NU1015-ML Cylindrical Roller SKF open CN 58.3 71 750
NUP1015 Cylindrical Roller NTN open CN 66.5 74.5 727

Note: catalogue dynamic load ratings for this envelope span 41.6– 66.5 kN — a 60% spread between designs in the very same 75×115×20 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 75 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6015, 6015-2RS, 6015-2RS-NSK, 6015-2RS-NTN, 6015-M, 6015-NSK, 6015-NTN, 6015-RSR, 6015-RSR-NSK, 6015-RSR-NTN, 6015-ZZ, 6015-ZZ-NSK, 6015-ZZ-NTN, 7015, 7015-NTN, N1015, NJ1015, NU1015, NU1015-ML, NUP1015.

Frequently asked questions

Are all 75×115×20 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 75 mm bore, 115 mm OD, 20 mm width (2.953×4.528×0.787 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 20 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 75×115×20?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 75×115×20 mm in inches?

75×115×20 mm converts to 2.953×4.528×0.787 in, with a 20 mm (0.787 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6015, 6015-2RS, 6015-2RS-NSK mount in the same space despite different internal designs.