7317-BECBM bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7317-BECBM model number is decoded

7317 BECBM is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 156 kN, C0 132 kN, Pu 4.9 kN.reference speed 4,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 4450 g. Mass and section check: 4450 g inside the 85×180×41 mm outline leaves a 47.5 mm radial section, and the 132 kN static rating is 0.85× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 4.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 156/132 kN ratings and 4450 g mass this execution carries about 1.84 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 6,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.75. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Fillet radii must clear the chamfer so the 41 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.
• Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.
• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• The steep 40° angle of 7317-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.