6034-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6034-FAG model number is decoded

6034 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-light 60xx section (diameter series 0 of ISO 15), multiplying bore code 34 by five gives the 170 mm bore; the 260 mm outside diameter and 42 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 170 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 170 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 60xx extra-light section at 170 mm bore uses a smaller 260 mm OD than a 6234; load ratings are lower, so do not replace a failed 62-series bearing with a 60-series without re-rating the load.
• The open 6034-FAG has no lubricant retention: grease escapes and contaminants migrate straight into the 170×260×42 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 6034-FAG leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 42 mm-wide ring of 6034-FAG drags the lip and overheats it.
• The housing bore for the 260 mm OD should be round within IT7; an oval bore pinches the outer ring of 6034-FAG and shows up later as two-point loaded raceway wear.
• The open 6034 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• FAG lists the mechanical limiting speed at 3400 r/min for 6034 (thermal reference speed 3550 r/min); the thermal reference speed is the binding figure for continuous duty — size the lubrication interval off the reference speed, not the mechanical limit.
• The 170 mm bore places 6034 in Schaeffler's large-size range; at these diameters the pressed steel cage is speed-limited and FAG commonly offers a machined brass cage (suffix M) as an option. Verify cage material and relubrication provision with the distributor, and do not extrapolate small-bore speed ratings to this size.
• FAG rates 6034 at 179 kN dynamic (C) and 172 kN static (C0); this is an extreme-load rating at the top of the HR 1 single-row deep-groove range, where mounting, shaft stiffness and housing alignment dominate achievable life — request a Schaeffler application review rather than relying on catalogue L10 alone.
• At 7100 g (7.1 kg), 6034 is a heavy FAG bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 170×260×42 mm envelope of 6034 gives a D/d ratio of 1.53 and 45.0 mm radial section height — a thin FAG section that saves space but is sensitive to misalignment and shock; keep the housing round within IT7 and the shaft deflection below the raceway contact envelope.
• The 179/172 kN load ratings, mass 7100 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6034-FAG on the 170×260×42 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6034 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Mixing old and new FAG generations of the same designation in one arrangement is dimensionally acceptable, but where ratings matter — preloaded or matched sets — order both positions from the same generation and lot.
• FAG sealed units arrive greased for life with a lithium-soap fill; Schaeffler quotes a shelf life for greased bearings and recommends running stock first-in-first-out rather than re-greasing aged sealed units.