61800-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61800-2RS-FAG model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61800 carries bore code 10 = 10 mm. Outside diameter 19 mm and width 5 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 10 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. Schaeffler HR 1 catalogues the lip-contact sealed version as 61800-2RSR (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 10 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61800 with C3 for those conditions.
• Only 4.5 mm of radial section separates bore and OD on the 618xx series at 10 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6210.
• Contact seals add drag and heat: 61800-2RS-FAG runs slower and cooler-limited than the open 61800; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Heat is the enemy of the sealed 61800-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 61800-2RS-FAG-C3. No clearance suffix means normal CN clearance.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Schaeffler HR 1 lists the lip-contact sealed version as 61800-2RSR (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• FAG rates 61800 at 21000 r/min mechanical limiting speed — a high-speed range where the thermal reference speed governs continuous duty; use low-viscosity turbine oil or high-speed grease and avoid lip-contact seals entirely.
• At 10 mm bore the 61800 sits in Schaeffler's miniature range; HR 1 ships these sizes with a pressed steel or plastic cage and P0 tolerance as standard — for instrument or spindle accuracy order the P6/P5 variant explicitly, since P0 runout figures will not hold.
• At 1.72 kN dynamic load rating (C) and 0.84 kN static (C0), 61800 is a light-load FAG bearing: L10 life above a few kN of equivalent load is short, so size up to a 62-series on the same bore if the duty sees shock or frequent starts.
• At only 6 g, 61800 is a lightweight FAG bearing that can be handled by hand; still press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 10×19×5 mm envelope of 61800 gives a D/d ratio of 1.90 and 4.5 mm radial section height — a standard FAG medium section balancing load capacity and speed; the standard cage is adequate up to the listed speeds and C3 clearance is the common hot-shaft choice.
• The 1.72/0.84 kN load ratings, mass 6 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61800-2RSR on the 10×19×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61800 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 61800; the standard NBR lip is the economical general-duty choice, not the high-temperature one.
• Schaeffler has moved many HR 1 sizes to the X-life generation with higher C/C0 ratings; the designation is unchanged, so a current eKatalog listing for 61800 may quote higher values than the HR 1 print figures on this page — the envelope is identical either way.