61800-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61800-RSR-NTN model number is decoded

61800-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 10 by five gives the 10 mm bore; the 19 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 10 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6800LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 10 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 61800 with C3 clearance and re-check the residual value after mounting.
• The 618xx thin section at 10 mm bore has only a 4.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6210.
• RSR low-friction seals on 61800-RSR-NTN run faster than contact-seal 61800-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61800-2RS instead.
• The non-contact lip of 61800-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 10 mm bore position before relying on it as sealed-for-life.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 5 mm-wide ring of 61800-RSR-NTN drags the lip and overheats it.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• NTN catalogues this low-friction non-contact seal as 6800LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 10 mm bore the 61800 sits in NTN's miniature range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• The 32000 r/min grease limiting speed puts 61800 in NTN's high-speed range; at these speeds relubrication interval shortens sharply and the pressed-steel cage must be checked for cage-bar critical speed.
• At 2.03 kN dynamic load rating (C) and 0.93 kN static (C0), 0.07 kN fatigue load limit Cu, 61800 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 5 g, 61800 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 10×19×5 mm envelope of 61800 gives a D/d ratio of 1.90 and 4.5 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 2.03/0.93 kN load ratings, 0.07 kN fatigue load limit Cu NTN lists the grease limiting speed at 32000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 5 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6800LLB on the 10×19×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61800 in a rated drive.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61800 is listed.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.