61800-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61800-FAG model number is decoded

61800 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 10 by five gives the 10 mm bore; the 19 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 10 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 10 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 61800 with C3 for those conditions.
• The 618xx thin section at 10 mm bore has only a 4.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6210.
• Storage matters for open bearings: 61800-FAG leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61800 units.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61800-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• The open 61800 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• The 54000 r/min mechanical limiting speed puts 61800 at the top of the HR 1 deep-groove speed range (thermal reference speed 27500 r/min); at these speeds cage design and grease shear dominate — run open with oil-mist or air-over-oil lubrication and verify the thermal reference speed for the actual load before committing.
• At 10 mm bore the 61800 sits in Schaeffler's miniature range; HR 1 ships these sizes with a pressed steel or plastic cage and P0 tolerance as standard — for instrument or spindle accuracy order the P6/P5 variant explicitly, since P0 runout figures will not hold.
• At 1.72 kN dynamic load rating (C) and 0.84 kN static (C0), 61800 is a light-load FAG bearing: L10 life above a few kN of equivalent load is short, so size up to a 62-series on the same bore if the duty sees shock or frequent starts.
• The 10×19×5 mm envelope of 61800 gives a D/d ratio of 1.90 and 4.5 mm radial section height — a standard FAG medium section balancing load capacity and speed; the standard cage is adequate up to the listed speeds and C3 clearance is the common hot-shaft choice.
• The 1.72/0.84 kN load ratings here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61800-FAG on the 10×19×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61800 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler has moved many HR 1 sizes to the X-life generation with higher C/C0 ratings; the designation is unchanged, so a current eKatalog listing for 61800 may quote higher values than the HR 1 print figures on this page — the envelope is identical either way.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 61800; the standard NBR lip is the economical general-duty choice, not the high-temperature one.