61907-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61907-FAG model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61907 carries bore code 07 = 35 mm. Outside diameter 55 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 35 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 35 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 61907-FAG.
• The 619xx thin section at 35 mm bore (10.0 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• The open 61907-FAG has no lubricant retention: grease escapes and contaminants migrate straight into the 35×55×10 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61907 units.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Measure the shaft, do not trust the drawing: a 35 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61907-FAG.
• The open 61907 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• FAG rates 61907 at 17800 r/min mechanical limiting speed (thermal reference speed 10000 r/min) — electric-motor territory; prefer the open or 2Z execution (sealed 2RSR variants lose roughly a third of the thermal speed) and confirm grease life at the reference speed for continuous running.
• The 35 mm bore puts 61907 in Schaeffler's general-purpose industrial range; the standard cage and CN clearance cover most electric-motor and pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• FAG rates 61907 at 10.9 kN dynamic (C) and 7.75 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At 76 g, 61907 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 35×55×10 mm envelope of 61907 gives a D/d ratio of 1.57 and 10.0 mm radial section height — a thin FAG section that saves space but is sensitive to misalignment and shock; keep the housing round within IT7 and the shaft deflection below the raceway contact envelope.
• The 10.9/7.75 kN load ratings, mass 76 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61907-FAG on the 35×55×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61907 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler's medias/eKatalog is the live source for the current execution of 61907: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.
• FAG standard tolerance for this size is P0 (PN); P6/P5 precision executions exist for spindle-adjacent duty but carry different order numbers in the Schaeffler system — they are not a selectable sorting of standard stock.