61907-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61907-NTN model number is decoded

61907 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 07 by five gives the 35 mm bore; the 55 mm outside diameter and 10 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 35 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 35 mm shaft for 61907 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• The 619xx thin section (10.0 mm section height at 35 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• Storage matters for open bearings: 61907-NTN leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61907 units.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61900-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Never mix components between two 61907-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• The open 61907 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 35 mm bore puts 61907 in NTN's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• NTN rates 61907 at 12000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the housing.
• NTN rates 61907 at 10.6 kN dynamic (C) and 6.85 kN static (C0), 0.49 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 74 g, 61907 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 35×55×10 mm envelope of 61907 gives a D/d ratio of 1.57 and 10.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 10.6/6.85 kN load ratings, 0.49 kN fatigue load limit Cu NTN lists the grease limiting speed at 12000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 74 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6907 on the 35×55×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61907 in a rated drive.
• Order the C3 internal-clearance version (61907 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.