61907-ZZ-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61907-ZZ-FAG model number is decoded

61907-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 07 by five gives the 35 mm bore; the 55 mm outside diameter and 10 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 35 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogue order number: 61907-2Z (FAG suffix 2Z), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 61907-ZZ-FAG; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• The 619xx thin section at 35 mm bore (10.0 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• ZZ shields are non-contact: 61907-ZZ-FAG blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 61907-2RS for that.
• Shielded 61907-ZZ-FAG units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 10 mm-wide ring of 61907-ZZ-FAG drags the lip and overheats it.
• A 35 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Schaeffler HR 1 lists the shielded version as 61907-2Z — FAG suffix 2Z, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the FAG order number when buying through a Schaeffler channel.
• FAG rates 61907 at 15100 r/min mechanical limiting speed (thermal reference speed 10000 r/min) — electric-motor territory; prefer the open or 2Z execution (sealed 2RSR variants lose roughly a third of the thermal speed) and confirm grease life at the reference speed for continuous running.
• The 35 mm bore puts 61907 in Schaeffler's general-purpose industrial range; the standard cage and CN clearance cover most electric-motor and pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• FAG rates 61907 at 10.9 kN dynamic (C) and 7.75 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At 76 g, 61907 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 35×55×10 mm envelope of 61907 gives a D/d ratio of 1.57 and 10.0 mm radial section height — a thin FAG section that saves space but is sensitive to misalignment and shock; keep the housing round within IT7 and the shaft deflection below the raceway contact envelope.
• The 10.9/7.75 kN load ratings, mass 76 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61907-2Z on the 35×55×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61907 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 61907; the standard NBR lip is the economical general-duty choice, not the high-temperature one.
• FAG sealed units arrive greased for life with a lithium-soap fill; Schaeffler quotes a shelf life for greased bearings and recommends running stock first-in-first-out rather than re-greasing aged sealed units.