6202-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6202-2RS-NTN model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6202 carries bore code 15 = 15 mm. Outside diameter 35 mm and width 11 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 15 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's contact-seal catalogue number is 6202LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 15 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6202 with C3 for those conditions.
• The 62xx light series is the default general-purpose section at 15 mm bore; before upgrading to a 6315 for extra capacity, confirm the housing accepts a 35 mm OD and 11 mm width — it is not a drop-in swap.
• Contact seals add drag and heat: 6202-2RS-NTN runs slower and cooler-limited than the open 6202; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Heat is the enemy of the sealed 6202-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 35 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6202-2RS-NTN.
• NTN catalogues the contact-sealed version as 6202LLU (suffix LLU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• At 15 mm bore the 6202 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• NTN rates 6202 at 15000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• NTN rates 6202 at 8.6 kN dynamic (C) and 3.6 kN static (C0), 0.28 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At only 45 g, 6202 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×35×11 mm envelope of 6202 gives a D/d ratio of 2.33 and 10.0 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 8.6/3.6 kN load ratings, 0.28 kN fatigue load limit Cu NTN lists the grease limiting speed at 15000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 45 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6202LLU on the 15×35×11 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6202 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Order the C3 internal-clearance version (6202 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.