6202-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6202-2RS-FAG model number is decoded

6202-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 15 by five gives the 15 mm bore; the 35 mm outside diameter and 11 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogues the lip-contact sealed version as 6202-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 15 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6202 with C3 clearance and re-check the residual value after mounting.
• At 15 mm bore the 62xx light series is the workhorse section; its 35×11 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• Contact seals add drag and heat: 6202-2RS-FAG runs slower and cooler-limited than the open 6202; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Never wash a sealed 6202-2RS-FAG in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 6200-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Never mix components between two 6202-2RS-FAG units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• Schaeffler HR 1 lists the lip-contact sealed version as 6202-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• FAG rates 6202 at 19400 r/min mechanical limiting speed — a high-speed range where the thermal reference speed governs continuous duty; use low-viscosity turbine oil or high-speed grease and avoid lip-contact seals entirely.
• At 15 mm bore the 6202 sits in Schaeffler's small-bore range; HR 1 ships these sizes with a pressed steel or plastic cage and P0 tolerance as standard — for instrument or spindle accuracy order the P6/P5 variant explicitly, since P0 runout figures will not hold.
• FAG rates 6202 at 8.9 kN dynamic (C) and 3.75 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At only 44 g, 6202 is a lightweight FAG bearing that can be handled by hand; still press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×35×11 mm envelope of 6202 gives a D/d ratio of 2.33 and 10.0 mm radial section height — a heavy FAG section for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 8.9/3.75 kN load ratings, mass 44 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6202-C-2HRS on the 15×35×11 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6202 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• FAG standard tolerance for this size is P0 (PN); P6/P5 precision executions exist for spindle-adjacent duty but carry different order numbers in the Schaeffler system — they are not a selectable sorting of standard stock.
• Schaeffler's medias/eKatalog is the live source for the current execution of 6202: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.