6202-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6202-RSR-NTN model number is decoded

6202-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 15 by five gives the 15 mm bore; the 35 mm outside diameter and 11 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6202LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 15 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 6202 against the shaft shoulder while it cools so the ring cannot creep back.
• At 15 mm bore the 62xx light series is the workhorse section; its 35×11 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• The low-drag lip of 6202-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 6202-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 15 mm bore position before relying on it as sealed-for-life.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 11 mm-wide ring of 6202-RSR-NTN drags the lip and overheats it.
• Measure the shaft, do not trust the drawing: a 15 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6202-RSR-NTN.
• NTN catalogues this low-friction non-contact seal as 6202LLB (suffix LLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 15 mm bore the 6202 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• NTN rates 6202 at 18000 r/min grease limiting speed — this is a high-speed electric-motor range; keep the grease fill at 20–30% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• NTN rates 6202 at 8.6 kN dynamic (C) and 3.6 kN static (C0), 0.28 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At only 45 g, 6202 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×35×11 mm envelope of 6202 gives a D/d ratio of 2.33 and 10.0 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 8.6/3.6 kN load ratings, 0.28 kN fatigue load limit Cu NTN lists the grease limiting speed at 18000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 45 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6202LLB on the 15×35×11 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6202 in a rated drive.
• Order the C3 internal-clearance version (6202 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• Standard catalogue stock of 6202 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.