6216-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6216-2RS-NTN model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6216 carries bore code 16 = 80 mm. Outside diameter 140 mm and width 26 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 80 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's contact-seal catalogue number is 6216LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 80 mm of 6216-2RS-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 62xx light series is the default general-purpose section at 80 mm bore; before upgrading to a 6316 for extra capacity, confirm the housing accepts a 140 mm OD and 26 mm width — it is not a drop-in swap.
• Heat is the enemy of the sealed 6216-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6216-2RS-NTN in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6216-2RS-NTN-C3. No clearance suffix means normal CN clearance.
• Measure the shaft, do not trust the drawing: a 80 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6216-2RS-NTN.
• NTN catalogues the contact-sealed version as 6216LLU (suffix LLU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• At 80 mm bore 6216 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 3000 r/min for 6216; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 80.5 kN dynamic load rating (C) and 53 kN static (C0), 3.95 kN fatigue load limit Cu, 6216 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 1400 g (1.4 kg), 6216 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 80×140×26 mm envelope of 6216 gives a D/d ratio of 1.75 and 30.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 80.5/53 kN load ratings, 3.95 kN fatigue load limit Cu NTN lists the grease limiting speed at 3000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 1400 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6216LLU on the 80×140×26 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6216 in a rated drive.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 6216 is listed.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.