6216-ZZ bearing: complete specifications & equivalents
The 6216-ZZ is a ISO 15 radial bearing sized 80 x 140 x 26 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 80 mm |
| Outer diameter D | 140 mm |
| Width B | 26 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 72.8 kN |
| Basic static load rating C0 | 55 kN |
| Fatigue load limit Pu | 2.2 kN |
| Reference speed (thermal) | 9500 rpm |
| Limiting speed (mechanical) | 4800 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 1550 g |
| Manufacturer designation | SKF 6216-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 5.512 in |
| Width B | 1.024 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 25 of 45 |
| Bore above smallest 6200-series size | 77 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6216 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
| 6216-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×140×26 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6216-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×140×26 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6216-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×140×26 mm envelope per ISO 15; seal variant differs (ZZ vs RSR) — confirm sealing suits the duty. |
| 6216-ZZ-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6216-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×140×26 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6216-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×140×26 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6216-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×140×26 mm envelope per ISO 15; seal variant differs (ZZ vs RSR) — confirm sealing suits the duty. |
| 6216-ZZ-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7216 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| NU216 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| 6216-M | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF 6216 M (machined brass cage, open arrangement) is the same-size execution on the 80×140×26 mm envelope with ratings within 10 % — boundary dimensions interchangeable. |
| 216 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 216 shares the 80×140×26 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
| 216-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 216-2Z shares the 80×140×26 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6216-ZZ model number is decoded
6216-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 16 by five gives the 80 mm bore; the 140 mm outside diameter and 26 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 80 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. SKF's own suffix is 2Z (this page's industry-neutral spelling is -ZZ); catalogue number 6216-2Z.
Typical equipment & failure modes
Common applications
- medium and heavy industrial drives
- large gearboxes
- industrial fans and blowers
- hoists and winches
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- electrical pitting in VFD-driven motors without grounding protection
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Large bores like the 80 mm of 6216-ZZ demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
- The 62xx light series is the default general-purpose section at 80 mm bore; before upgrading to a 6316 for extra capacity, confirm the housing accepts a 140 mm OD and 26 mm width — it is not a drop-in swap.
- ZZ shields are non-contact: 6216-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6216-2RS for that.
- Shielded 6216-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
- Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
- Suffixes stack in a defined order — clearance follows the seal code, e.g. 6216-C3. No clearance suffix means normal CN clearance.
- SKF spells the shielded version 6216-2Z (one shield: 6216-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The single-shield execution 6216-Z is a distinct order number in catalogue 17000: it suits open gears or oil-bath arrangements where the unshielded face faces the lubricant, and it is not interchangeable with the double-shield 6216-2Z for high-contamination positions.
- The 72.8/55 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6216-ZZ bearing?
A 6216-ZZ deep-groove ball bearing has a 80 mm bore, 140 mm outer diameter and 26 mm width (3.15 × 5.512 × 1.024 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields.
How does the 6216 bore code work?
The last two digits of 6216 are bore code 16, giving 16 × 5 = 80 mm bore. The 140 mm outside diameter and 26 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the ZZ suffix on 6216-ZZ mean?
ZZ means two non-contact sheet-metal shields, one each side. They retain factory grease and block coarse particles with little friction, but do not seal against liquids, fine dust or pressure washing.
How does the 6200 compare with other series at the same 80 mm bore?
The '2' is the light diameter series: 140×26 mm with a 30.0 mm radial section at 80 mm bore. A 6316 on the same bore is larger and higher-rated; a 6016 is smaller and lower-rated.
What is the SKF designation and catalogue data for 6216-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 6216-2Z — two non-contact sheet-metal shields, 80×140×26 mm per ISO 15. Quoted values: C 72.8 kN, C0 55 kN, Pu 2.2 kN, limiting speed 4800 r/min, mass 1550 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6216-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.